Current location - Education and Training Encyclopedia - Educational Knowledge - Details of the Construction and Training of Qingdao Vocational Education Public Training Base
Details of the Construction and Training of Qingdao Vocational Education Public Training Base
(1) In 2006, the Development and Reform Commission of Qingdao officially approved the construction of a public training base for vocational education in Qingdao, with an investment of 1.32 million yuan and an area of 174 mu, which was listed as one of the ten practical things that Qingdao did that year.

The training base is located in Qingdao High-tech Zone, south of Shandong Light Industry Engineering School, with a building area of 42 150 square meters. The design receives 9600 engineering practice students every year. There are six standard training workshops including construction machinery (molds), numerical control, electromechanical, welding, auto repair and chemical industry, and supporting facilities such as accommodation, canteen and office. The construction area of each workshop is 2,260 square meters, of which the investment in training equipment is 4 1 10,000 yuan, and the training equipment of the training base is 7 million yuan supported by the Ministry of Education and the Ministry of Finance, mainly including two workshops, namely, CNC and auto repair.

Statistical table of training base equipment

Installation and debugging of quantity value of workshop equipment

1 Processing 2.7 million yuan has been installed and debugged.

2 welding 2.5 million is being installed and debugged.

3 CNC120,000 has been installed and debugged.

4. 2,654.38 million electromechanical units have been installed and debugged.

5. 3.6 million yuan of auto repair has been installed and debugged.

6.5 million molds have been installed and debugged.

(2) The construction of Qingdao vocational education public training base has been approved by Qingdao Editorial Committee. The training base is a deputy bureau-level institution managed by Qingdao Education Bureau. According to the needs of the training base, the staffing is approved by stages. Staff are being recruited according to the progress of work.

(3) Training form

According to the arrangement of the Education Bureau, the training base received 2000 trainees in the second half of 2008. In 2009, 5,000 people were trained, reaching 7,000 in 2065, 438+00 and10000,438+01in 2065.

Training forms mainly take the following three forms:

1. Vocational skill training and appraisal. The main purpose is to help students complete the training and assessment of vocational skills through three months of practical training;

2. Comprehensive training for half a year. Focus on professional skills, focusing on building students' basic skills, professional skills and comprehensive skills;

3. Menu-based training. According to the different teaching needs of vocational schools (some need basic skills training, some need some professional skills training, etc.). ), the training base will conduct menu-based training from the most basic training to the final textual research training and comprehensive training.

Numerical control training workshop

The workshop covers an area of 2260 square meters. The workshop can train over 800 people at the same time. Equipment investment120 thousand, with modern equipment. There are 42 lathes, including more than 30 economical lathes and 0/02 full-function lathes. The systems mainly include Guangzhou system, Central China system and Fanac. There are more than 20 milling machines and machining centers, including 4 four-axis linkage machining centers. The systems mainly include Guangzhou system, Central China system and Fanac. At the same time, the workshop also has CMM and other equipment, as well as two simulation classrooms.

The workshop is mainly divided into three areas: lathe training area, milling machine training area and simulation training area. The training area of CNC lathe is mainly to learn the basic operation, programming, parts processing and maintenance of lathe. Milling machine training area is mainly to learn the basic operation, programming, parts processing and maintenance of milling machine and machining center. Simulation is mainly to let students simulate the operation of machine tools on the computer and check whether the program is correct.

The workshop mainly completes the practical teaching, project-based teaching and skill training for students in five cities and three districts for half a year; Through the examination, I obtained the professional qualification certificates of lathe, milling and machining center.

At the same time, CNC workshops carry out school-enterprise cooperation business, undertake parts processing business and product development.

Electromechanical training workshop

The electromechanical training workshop covers an area of 2,260 square meters, and more than 600 people can be trained at the same time, with modern equipment. Includes six closed training rooms and one open training room. Among them, the hydraulic and pneumatic training room has 8 sets of hydraulic and pneumatic training equipment, the electrical assembly training room has 57 sets of electrical assembly test beds, the general machine tool troubleshooting and examination training room has 6 sets of machine tool physical simulation test beds, the PLC simulation and application training room has 27 sets of PLC simulation and application test beds, the single-chip computer simulation and application training room has 100 sets of electronic assembly training rooms, and the open refrigeration training room.

The mechanical and electrical training workshop mainly completes half-year practical teaching, project teaching and skill training for students in five cities and three districts; After passing the examination, he obtained the professional qualification certificate of maintenance electrician, home appliance repairman and electronic assembler.

At the same time, the electromechanical training workshop carries out school-enterprise cooperation business and undertakes maintenance business and product development.

Automobile maintenance training workshop

The auto repair training workshop covers an area of 2,260 square meters and can arrange more than 400 people for training at the same time. The equipment investment is more than 4 million, and there are more than 200 sets of various equipment. The workshop is divided into maintenance area and teaching area. The teaching area is mainly professional training, including three parts: automobile engine, automobile chassis and automobile electrical appliances. The maintenance area mainly carries out comprehensive fault diagnosis and maintenance, and can operate l2 vehicles at the same time.

The first part of the teaching area is the engine training area, with 10 Santana 2000 engine for students to disassemble. Through disassembly, students can master the structure and composition of EFI engine. There are four AJR electronic control gasoline engine training platforms, and special computer testing equipment such as Toyota and Honda, which can be used for students to troubleshoot various electronic control engines.

The second part of the teaching area is the automobile chassis training area, which has four manual/automatic transmission training platforms and two ABS system training platforms for students to disassemble, repair and troubleshoot the automobile chassis.

The third part of the teaching area is the electrical training area, which includes two general electric test benches, two full-vehicle circuit signal and lighting system test benches, two automobile electronic and electrical simulation system training benches, two automobile electric control doors and central locking training benches, two automobile airbag test benches and a manual air conditioning test bench, which can be used for students to carry out automobile electrical training and simulate automobile troubleshooting.

There are 12 stations in the automobile maintenance area, and the main equipment includes spray paint room, automobile molding machine, four-wheel aligner, tire scraper, wheel dynamic balancer and other equipment, which can meet all kinds of automobile maintenance operations.

The auto repair workshop mainly completes half-year practical teaching, project teaching and skill training for students in five cities and three districts; After passing the examination, he obtained the professional qualification certificate of automobile maintenance workers and other types of work.

At the same time, the auto repair workshop carries out school-enterprise cooperation business and maintains various vehicles.

Welding training workshop

The welding training workshop covers an area of 2,260 square meters and can arrange more than 300 people for training at the same time. It has more than 30 sets (sets) of modern welding equipment/KLOC-0, and has two major areas: welding practice area and welding demonstration area. The welding practice area includes three parts: covered electrode arc welding, CO2 gas shielded welding and TIG welding. The welding demonstration area can show students all kinds of modern commonly used welding equipment.

The first part of the practice area is the covered electrode arc welding training area. There are 20 AC arc welding machines and 20 DC arc welding machines, and more than 100 people can be arranged to participate in covered electrode arc welding training at the same time. There are 20 AC arc welding machines and 20 DC arc welding machines, and more than 120 people can be arranged to participate in covered electrode arc welding training at the same time.

The second part of the practice area is the carbon dioxide gas shielded welding training area. There are 40 semi-automatic CO2 shielded welding machines, and more than 120 people can attend CO2 shielded welding training at the same time.

The third part of the practice area is the TIG welding training area. At present, there are 10 tungsten pulse argon arc welding machine and 10 DC argon arc welding machine, and more than 60 people can be arranged to attend covered electrode arc welding training.

The welding demonstration area has modern welding equipment such as fully digital MIG/MAG multifunctional welding machine, fully digital TIG welding machine, plasma water cutting machine, microcomputer screen display hydraulic universal testing machine, arc welding robot, etc., which can be demonstrated and taught to students on site.

The welding training workshop is mainly used for students' welding training, modular teaching, internship, short-term training for social personnel, CIMC and other enterprise employees' training and assessment of various welding skills, and the combination of production and education is implemented.

Mechanical training workshop

The machining training workshop covers an area of 2,260 square meters, and more than 600 people can be trained at the same time. The equipment investment is more than 5 million, and it has a large number of production and processing equipment. Among them, there are 40 C6 140 general lathes, more than 200 locksmith stations, and several milling machines, grinders and other equipment.

The workshop is mainly divided into three areas: lathe training area, fitter training area and other machine tool training areas. The lathe training area is mainly to learn the basic operation of lathe, the processing of parts and the maintenance of lathe. The fitter training area is mainly to learn the use of various measuring tools and the contents of filing, sawing, drilling and assembling; Other machine tool training areas mainly study milling and planing.

The machining workshop mainly completes half-year practical teaching, project teaching and skill training for students in five cities and three districts; Carry out social training, long-term and short-term training and yellow gold blue-collar training. After the training, organize the examination of middle and senior technicians, and obtain the professional qualification certificates of lathe workers, locksmiths and other trades after passing the examination.

Mold training workshop

The mold training workshop has complete supporting equipment for modern mold industry, including five functional modules: machining training area, special machining training area, mold fitter training area, product trial processing training area and mold simulation training area, and can arrange more than 200 people for training at the same time.

There are two full-function CNC milling machines, 1 CNC lathe, two turret milling machines and two precision grinders in the processing area. The special processing zone has four fast WEDM and EDM machines in Dimonkate, Beijing, four new WEDM and WEDM machines in Suzhou and two precision engraving and milling machines. There are 6 stations and 36 stations in the die fitter's area, with a full set of marking tools and fitter's tools, multiple radial drilling machines and bench drills, and 10 sets of plastic and stamping dies for students to disassemble and assemble, which can be used for the training of middle and senior die fitters and technicians. There are injection molding machines, injection molding machines, injection simulators, crank presses, four-column hydraulic presses, as well as transparent mold teaching AIDS for teaching, which can be directly used for injection molding and stamping demonstration; There are 50 Founder brand computers in the mold simulation area, which are equipped with genuine software such as UGNX5.0, Huasu WEDM simulation, Moldflow mold flow analysis, AutoCAD, Yulong numerical control simulation, and can be trained in UG, NC and other related skills.

The mold training workshop can complete the practical teaching, modular teaching and skill training of students in five cities and three districts, carry out long-term and short-term social training and golden blue-collar training, and organize the examination for senior technicians recognized by the Ministry of Education and the Ministry of Labor. After passing the examination, you can obtain the professional qualification certificates of senior technicians such as mold manufacturer, CNC milling machine worker and UG. Can also undertake the training of senior teachers in mold specialty; At the same time, through the cooperation with foreign schools and enterprises, we can undertake the work of plastic, cold stamping die processing and product development.