How to tune the guzheng? How to tune the new guzheng?

The tuning of guzheng is a very difficult problem for beginners, but you can master it as long as you have some training and know how to tune it. Here are ways to tune with overtones and octaves:

Take the scale of 2 1 chord d as an example. First, use a tuning whistle or a fixed pitch instrument to make a standard tone, that is, the tonic of the tone. Then, according to the octave relationship, call out all the tonic tones in D, namely bass 1, bass 1, alto 1, treble 1, and treble 1.

At this time, you need the ability to distinguish octaves. In order to further test the accuracy of these tonic sounds, you can also play overtones in half of each tone and further fine-tune. After this alignment, the first step is completed;

The second step is the key step, which is to find the overtone of 5 on "bass 1". This overtone is located at one third of the chord length between Yanzhu (Qin code) and Yueshan, and the pitch difference between the overtone played and the local tone is 12 degrees, so the overtone played at one third of "double bass 1" is practical.

Step 3, find out the overtone 2 that is one-third of the chord length of the "bass 5" sound, and then call out all the two sounds in the sound system, namely "bass 2, bass 2, midrange 2 and treble 2";

Step 4, find out the overtone 6 in the upper third of the "double bass 2" tone, and then send out all 6 tones;

The last step is to find 3 in the upper third of the 6 tones, and then call out all 3 tones, so that all the tones can be heard. Please refer to the attached drawings:

If there is Andhadhun, it will be much more convenient to tune the strings. The method and steps of tuning the strings are the same as those mentioned above. The first step is to adjust all 1 tones. The second step is to call out all five sounds; The third part calls out both sounds; Step four, call out all six sounds; Step 5: Call up all three tones. That is to say, tune the strings in the order of five degrees of 1, 5, 2, 6, 3(D, a, e, b, f). When adjusting each tone, it is best to set the tuner pointer to the middle position.

How to tune the guzheng? Tune the guzheng.

The tuning method of guzheng is as follows:

First, ask teachers or friends for help, preferably friends with good feelings and close families; This helps to tune the piano frequently.

Second, buy a tuner, because the tuner is electro-mechanical tuning, which is very easy to use and can be used at any time, so it is easy to solve the tuning problem.

Without Andhadhun, we should keep the tone accurate. In addition to having a good sense of music, we should also master the tuning technology and gradually achieve accurate, fast and good sound quality in training.

Tuning method: A. Set the first sound first: Generally, it is better to set the standard sound A' of the 14th string first. Tune the string with a standard tuning fork or tuner, and tune it with a tuning wrench. B. Re-adjust octave: After a' is adjusted, the re-adjusted octave is A (ninth string); One (the fourth string) and one "(the nineteenth string). C. According to the key to be set, use the five-degree and eight-degree cyclic method to adjust other keys-if the D key is set (generally used more), you can use the five-degree and eight-degree cyclic method to adjust other keys.

The method is: use A' sound to determine the E "sound (the sixteenth string) of the upper fifth degree, and use the method of listening to the pure fifth degree harmony; A is pronounced e '；; Tone (the twelfth string), using the octave harmony of e' and e "to correct the tone; The sound of a determines the sound of e (the seventh string), and the sound is corrected by the octave sum of e and e'; The e-note determines the e-note (second string). And so on, and then e "; B, b, b' and other fifth tones; In addition to the five-degree and eight-degree cycle tuning method, sometimes the four-degree tuning method is added. For example, after A' is adjusted to E', it can also be used to adjust E' (four-degree relationship). In addition, the pitch of the first string can be adjusted according to the string order of each string sound, and then the pitch of each string can be roughly adjusted one by one, and then the five-degree and eight-degree cyclic tuning method can be used for detailed tuning.

Scheme 2- Guzheng Andhadhun

First, assemble the sound calibrator:

1. Take out the package of the sound calibrator, which consists of the main unit, battery and pickup, and open the back cover of the main unit;

2. Install the sound calibrator, cover the back cover, and pay attention to distinguish the positive and negative poles of the battery;

3. Insert the pickup into the jack below the right side of the main unit.

Secondly, set the tuner:

1, use of key:

Press and hold the "Start" button on the tuner panel to turn off the tuner, then press and hold the "Start" button to turn it on and off;

2, know the calibration mode:

There is a guzheng logo in the upper left corner of the control panel, a tuning fork logo in the middle upper left corner, and a triangular arrow pointing to the guzheng position in the upper left corner of the LCD;

3. Choose guzheng mode:

Press the mode key lightly, and the triangular arrow points to the tuning fork position, indicating that the current tuning state is twelve average laws. Press the mode key lightly again, and the triangle arrow points to the position of Guzheng, indicating that the current tuning state is Guzheng. If it is not the state of the guzheng tuner, switch by pressing the mode key continuously;

How to use d-key guzheng?

How to tune the D-tone zither will be recommended to the following channels: the phoneme arrangement of the zither is arranged according to the fifth scale (12356), the standard tuning of the commonly used 2 1 string zither is D, the lowest tone is set to the big character group D, and the highest tone is set to the small character group d(d3).

D key position arrangement (from low to high, 2 1 string-1 string): 2 1 string, double bass 1(D) 20 strings, double bass 2(E) 19 strings, double bass 3 (. Bass 1(d) 15, Bass 2(e) 14, Bass 3(#f) 13, Bass 5(a) 12, Tone 6 (b)/kloc-0. Alto 3(#f 1) 8 strings, alto 5(a 1)7 strings, alto 6(b 1) 6 strings, alto 1(d2) 5 strings, alto 2(e2) 4 strings, alto 3 (. Guzheng D is based on our introductory etudes, which are basically in D major, and the entrance examination songs are basically in D major. So when we tune, we set the tuner to Guzheng D, A=440, which is automatic. When tuning, for example, if you tune the eighth string now, we only need to look at the number, and we don't need to look at the letters after the number. The tuning number just shows the number of strings, and then the green light shows it, indicating that the tuning is accurate. At first, the tuning is slow, and it is easy to break strings. It's best to check the video online.

There are also many video teaching tuning. I wish you success in learning Zheng.

How to tune the guzheng?

It may be caused by the wrong tuning method. The correct method is as follows.

If it still doesn't work after trying, it should be Andhadhun's problem. You can try again with another tuner. 1. Assemble the sound corrector: 1. Take out the package of the sound corrector, which consists of the host, the battery and the pickup, and open the back cover of the host; 2. Install the sound calibrator, cover the back cover, and pay attention to distinguish the positive and negative poles of the battery; 3. Insert the pickup into the jack below the right side of the main unit.

2. Set the tuner: 1. Use of on-off key: press and hold the "Start" key on the tuner panel to turn off the tuner, then press and hold the "Start" key to turn on the tuner, and press and hold the "Start" key to turn on and off the tuner; 2. Know the tuning and calibration mode: there is a guzheng sign in the upper left corner of the control panel, a tuning fork sign in the upper left corner, and a triangular arrow in the upper left corner of the LCD pointing to the position of the guzheng; 3. Select Guzheng mode: press the mode key lightly, and the triangular arrow points to the tuning fork position, indicating that the current tuning state is twelve average laws. Press the mode key lightly again, and the triangle arrow points to the position of guzheng, indicating that the current tuning state is guzheng, which is exactly what we need. If it is not in the state of the guzheng tuner, switch by continuously pressing the mode button; 4. Select tonality: there is a pointer in the lower left corner of the LCD, and there is a letter above the pointer, usually D, which means1= D. This is the tonality D key that we beginners need. If it is not D, you can press the Start key continuously to select, and the letters will be converted between CDEFGAB to achieve the tonality we need.

5. Manual tuning: You can select the desired tuning string by pressing the up and down arrows on the tuner. If you press the up key continuously, the number in the middle of the dashboard will gradually increase from 1 to 2 1 until it returns to 1. If the down button is pressed continuously, the number in the middle of the dashboard will go from 2 1 to 65438+. Third, start to calibrate the sound: 1. Install the Zheng code one by one according to our label position, and don't loosen the string; 2. Open the tuning box of the guzheng, and you will see a row of 2 1 metal chords inside. Clamp the clip of the pickup on a metal string wound by 2 1 string (the thickest string). It doesn't matter where the clip is, just connect it with the guzheng. According to our experience, the editing effect is the best when debugging 2 1 strings. 3. Select the eighth string: press the up/down key continuously, and the number in the middle of the dashboard will be displayed as 8A (the letter at the back represents the sound name, which is automatically generated without setting); 4. Gently dial the number 8 Zheng with your fingers to the position of the middle string of Yueshan. The force should not be too great, and the pointer will swing left and right on the instrument. When the pointer points to the position of 0 in the middle of the dashboard, the sound will be accurate when green is displayed. A there is a number -50 on the left side of LCD, a number +50 on the right side and a 0 in the middle. When we pluck the strings, the hands will switch between the dashboards. When the pointer is between 0 and -50, a red light indicates a low voice. When the pointer is between 0 and +50, a red light indicates a high sound. B, when the tone is low, tighten the strings clockwise, loosen the strings when the tone is high, and loosen them counterclockwise. The amplitude of tightening the strings should not be too large, which is equivalent to the amplitude of 3 minutes on the watch; C, note that the premise is to adopt manual calibration, and the number in the middle of the dashboard is consistent with the plucked string position. After the debugging of No.5.8 string is accurate, start debugging No.9 string, press the up key on the host computer, and it will be displayed as 9F# (the letter at the back represents the sound name, # represents the sharp sign, and B is the automatically generated flat sign without setting); According to the method of string 8 and so on.

Guzheng, also known as Han Zheng, Qin Zheng, Yao Zheng and Luan Zheng, is a traditional national musical instrument in China, belonging to plucked instruments. It is one of the important national musical instruments unique to China.

It has beautiful timbre, wide range, rich playing skills and strong expressive force, so it is deeply loved by the broad masses of the people. Now there are also small guzheng, portable guzheng, mini guzheng, semi-guzheng, new guzheng and twelve-tone guzheng.

Guzheng is an ancient national musical instrument, which was born and raised in this fertile yellow land with the long culture of China. It is a plucked musical instrument, and its structure consists of a panel, a wild goose column (also called Zheng code in some areas), strings, a front Yueshan, a string nail, a tuning box, a piano foot, a back Yueshan, a side plate, a sound outlet, a bottom plate and a string piercing hole.

The appearance of the guzheng is a rectangular wooden sound box, and the string frame "Zheng column" (that is, wild goose column) can move freely, and five sounds are arranged in one string. At first, there were the most 25-string zithers (Zheng was divided into Zheng), and there were 13 strings in Tang and Song Dynasties, and then it increased to 16, 18 and 2 1 string. At present, the most commonly used specification is 2 1 string; Generally, the models of guzheng are preceded by S 163-2 1, where S stands for the S-shaped Moon Mountain, which is Wang Xunzhi and Miao Jinlin * * *, 163 stands for the length of guzheng, and 2 1 stands for the number of strings of guzheng. Source: Baidu Encyclopedia Guzheng.

How to use d-key guzheng?

How to use d-key guzheng?

Your content will be recommended to the following channels:

The phoneme arrangement of guzheng is arranged according to the fifth scale (12356). At present, the standard tuning of 2 1 string guzheng is D, the lowest sound is set to large character group D, and the highest sound is set to small character group d(d3).

D Tuning position arrangement (from low to high, 2 1 string-1 string) order:

2 1 string, double bass 1(D)

20 strings, double bass 2(E)

19 string, double bass 3(#F)

18 string, double bass 5(A)

17 string, double bass 6(B)

16 chord, 1 bass (d)

15 string, bass 2(e)

14 chord, bass 3(#f)

13 string, bass 5(a)

12 chord, sound 6(b)

1 1 chord, alto 1(d 1)

10 chord, alto 2(e 1)

9 strings, alto 3(#f 1)

8 strings, alto 5(a 1

7 strings, alto 6(b 1)

6 strings, treble 1(d2)

5 strings, high note 2(e2)

4 strings, treble 3(#f2)

3 strings, high note 5(a2)

2 strings, treble 6(b2)

1 chord, treble 1(d3)

Note: () is the corresponding sound name.

Hello, the basis of Guzheng D is because our introductory etudes are basically in D major, and the test scores are basically in D major, so when we tune, we adjust the tuner to Guzheng D, A=440, which is automatic. When tuning, for example, if you tune the eighth string now, we only need to look at the number, and we don't need to look at the letters after the number. The tuning number just shows the number of strings, and then the green light shows it, indicating that the tuning is accurate. At first, the tuning is slow, and it is easy to break strings. It's best to check the video online. There are also many video teaching tuning. I wish you success in learning Zheng.

How to Tune with Guzheng Andhadhun

⑴ Open the outer package of the tuner, install the battery, and press and hold the (On/Off) key for three seconds to start the machine. The machine will start to display: Guzheng, press the (automatic) key to display: the letter "D" and a "440" of Guzheng. This is the correct startup display. You can tune the d key of guzheng. If you want to adjust other keys, please press the (automatic) key to convert.

⑵ Place the opened mixer directly in the mixer box, preferably with something soft on it. Put the tuning wrench on the pin to be tuned and start tuning. (Note: Guzheng chords need a sound, a ***2 1 chord)

(3) Take No.8 as an example:

A, play the eighth string and look at the numbers displayed on Andhadhun's display screen. Ignore the letters after the numbers.

B, if the displayed number is greater than 8, the string (screw on the No.8 string nail with a tuning wrench and turn it in time.

The needle is tight, and vice versa. The number displayed is less than 8, so the rope must be loosened.

C, the number shows 8, just look at the pointer. Special attention: this time the sound is close to the standard sound of this string, it must be

Turn the chord slowly. Tilt the pointer to the left and continue to tighten the rope. The pointer is to the right, so be sure to loosen the rope. Until the green light in the middle, the pointer is roughly in the middle.

D, and then tune other strings, and do the same. By analogy, all the strings are aligned (note: which string to tune,

The wrench will be sleeved on the corresponding chord nail).

E, when tuning each string, be sure to play more and watch Andhadhun, sometimes Andhadhun will connect it wrong.

Display error, be sure to play more and try more.

What should I do if the guzheng is always poorly tuned?

Your problem is always keeping a low profile, right? Is that the pointer can't point to the center and show the green light? Pointer left?

Actually, this is a simple method. Playing too much, or the music is too intense, or pushing too hard will lead to out of tune.

1, caused by uneven string tension: adjust each string (front and back) and press the left and right sides of the code several times with your left and right hands, so that it is not easy to get out of tune after the tension is balanced.

2, in the case of the best timbre, try not to move the code when tuning, only twist the chord to tune, which is always low, so push it out.

Push the wrench forward and tighten the strings. Be careful not to break them with too much force, but do it bit by bit.

3. The situation of not reaching the best timbre is caused by the placement of codes. Some panels do not fit the legs of the Zheng code, which causes the Zheng code to move left and right or back and forth after being fixed. For example, shaking a table with short legs leads to a tone change of one yard immediately after the tone is adjusted. Therefore, the code should be placed in a relatively flat position.

4. The problem of code placement is the same as above, but the situation is different. That is, the code is placed too far to the left, resulting in a very small string adjustment tension, which can't be adjusted tightly with a wrench at all, or it is broken until the corresponding pitch can't be reached. On the other hand, the code is too far to the right, the string is too loose, and it is easy to get out of tune.

This piano has been used for too long. Admittedly, due to repeated adjustment, the friction between the hole of the chord and the chord is too small, which leads to the sound reduction when playing. At this time, you can break the shaft handle in your own direction, unscrew the whole nail, wrap it with paper towel and screw it back (this method can only be used if it is really loose)

6, advanced music, intense playing, scratching, etc. lead to loose strings.

7. For Andhadhun, it is best to clip the piece near the strings of that key and play the strings at 1/2 with two fingers. Don't pluck the strings too hard or too lightly. Generally, it can be clipped on the code (seemingly inconvenient) and the corresponding chord nail. The best way is to cover the chord nail on the board above it (sorry, I don't know how to describe it).

The above is the rule that I summed up according to my previous playing experience and the situation that has happened. I hope it helps you. If you still don't understand, please keep asking questions. Thank you!

Zhu > _

How to tune guzheng

First of all, I'm not a professional. I don't know what your tuner is like. I've only seen two kinds, maybe the one you mentioned, but I haven't studied whether it's automatic or manual. One is very simple, just seven tones, 1234567. If you have a pitch, you can listen to this sound and then tune the guzheng. I think this is something that only experts can play. Ordinary people don't have that much skill to adjust. The other is that there are three electronic tuners on the display screen. If the small light is adjusted correctly, the middle one is green, and how to use the lower one (I said D). You put the tuner next to the Zheng and pluck the strings to see if the display at the top is not adjusted properly. 1-d 2-e 3-f well 5-a 6-b is definitely inaccurate according to the above adjustment, and the adjustment is to open the first piano. You know, there are professional wrenches. The relationship between piano sound and code is not much to say. For example, if you adjust a sound, moving the code to the left will decrease the pitch and moving the code to the right will increase the pitch. Note: Personally, if your strings are already tightly tuned, you can achieve the tuning effect by moving the piano code. When moving the Zheng code, you should lift the strings before moving, otherwise it will easily hurt the panel. That's all I know.