Safety operation rules for automobile mechanics. Check whether the tools used are in good condition before work. During the construction process, tools must be placed neatly and must not be misplaced. After the work, the tools should be counted, checked and wiped clean, and put into the tool cart or toolbox as required.
Second, when disassembling parts, appropriate tools or special tools must be used, and it is not allowed to be foolhardy, and it is not allowed to directly hit the parts with a hard hammer. All parts shall be placed neatly after disassembly, and shall not be piled up anywhere.
Three, waste oil should be poured into the designated waste oil drum collection, not back or into the drain, to prevent waste oil pollution.
Four, repair work should pay attention to protect the car paint luster, decoration, seats and carpets, and keep the vehicle clean and tidy. Smoking is not allowed in the workshop.
Five, when using jack for chassis operation, you must choose a flat and solid site and use angle wood to stabilize the front and rear wheels, and then use safety plates to stabilize the support points specified in the vehicle model. It is forbidden to simply jack up the vehicle and work under it.
Six, in the process of repair, should carefully check whether the original factory or replacement parts meet the technical requirements, and in strict accordance with the repair technical specifications for serious operation, inspection and debugging.
Seven, before starting the engine, should first check whether the components are correctly assembled, whether to add enough lubricating oil and cooling water in accordance with the provisions, put the transmission in neutral, gently start the motor test run. It is forbidden to start the vehicle when there are people under it.
Eight, when the engine overheating, shall not open the water tank cover, beware of boiling water burns.
Nine, the ground command vehicle driving, displacement, shall not stand in front of and behind the vehicle, and pay attention to the surrounding obstacles.
Safety operation rules for automobile interior repairmen 1. Indoor maintenance personnel must be familiar with maintenance equipment and tools and master the safe use methods.
2. Wear labor protection articles before work, make a safety speech before construction, and put forward safety production requirements according to specific work contents.
3, should clean up the scene before work, check the tools and equipment, make the scene have the conditions for safe work.
4, cleaning accessories must be carried out in a special basin, hands can't directly contact with strong corrosive items such as sodium hydroxide.
5. Smoking is prohibited in workshops and inspection sites.
6. The electrical equipment in the repair room should be checked regularly, and the voltage of the working lamp for repairing the car should not exceed 36 volts.
7, precision parts, are not allowed to knock, disorderly play, according to the technical requirements for assembly.
8, for leaded gasoline, it is strictly prohibited to use the mouth suction hose pump oil, in case of poisoning.
9. Kerosene (blank gasoline) should be used to clean accessories. If you need to clean accessories with gasoline or diesel, wash your hands with hot water soap immediately after work.
10, the maintenance site should be kept clean to achieve civilized production. After the work is completed, inflammable and explosive articles should be put in a safe place.
1 1. When trying to brake, you should choose a safe zone on a wide and straight section and pay attention to the front and rear vehicles. It is forbidden to test the brakes in the repair area.
12. In the vehicle maintenance area, fire fighting equipment must be equipped.
Safety operation rules for automobile maintenance electricians 1. Take care of installation and maintenance tools, and don't beat electrical equipment with a hammer.
2. When repairing the battery, you should wear protective glasses and acid-resistant gloves to prevent acid from overflowing, and flammable items are not allowed to be stored at the maintenance site.
3, at the end of the work, to inventory tools, to prevent left in the engine.
4, when cleaning parts with gasoline, it is forbidden to use open flame.
Safety operation rules for fitters in automobile maintenance 1. When using a hammer, check whether there are cracks and flash on the hammer head. Whether the hammer handle is loose or not, no one is allowed to stand opposite when using the hand hammer.
2. It is forbidden to hammer, shovel and rivet at work. Wear protective glasses at work and pay attention to people around you to avoid being hurt by iron nitrate.
3, when using power tools, must check whether there is any damage and leakage phenomenon.
4. When installing the workpiece, it is forbidden to put your hand into the movable screw eye to try it, so as to avoid squeezing injury.
5, must cut off the power supply before removing the equipment, no live operation.
6, the use of grinding wheel, drilling machine, lifting equipment, we must strictly abide by the safety operation specifications of the equipment.