The processing requirements of quartz stone are the same as those of natural stone, especially natural gneiss and granite. It is best for operators who process quartz stone to have experience in processing natural stone. Operators who have experience in processing general artificial stones, but have no experience in processing natural stones, must be trained before taking up their posts in principle. 1. Common machining tools: essential tools 1. 2 multifunctional marble cutting machines (cutting materials and chamfering edges). Grinding machine (equipped with special diamond grinding disc and resin grinding disc) 3. Cantilever water mill polisher 4. Hand drill (with diamond drill R 15-R45 mm)5. Curve data. Transparent) (2) Special adhesive for quartz stone (factory preparation) (3) Special dry adhesive for quartz stone (factory preparation) (4) Curing agent 2. According to the characteristics of diamonds, the recommended table shape is as follows: the back water retaining shape is a small arc R4-8 mm.

Front skirt with back water retaining at right angles to the table top: small circular arc R2-4 mm Quartz stone table top processing edge refer to page 28 of European Cabinet Technical Manual 2008. 3. On-site measurement, drawing and recording the size of the processing flow chart → confirming the color and edge shape of the countertop with customers → drawing templates and lines according to the drawings → cutting materials with a marble machine → trimming the edges with a multifunctional marble machine or other special water mill → blowing dry and cleaning the sticky water. Smear the adhesive surface → clamp it with a special fixture → remove the waste adhesive with a blade after curing → water mill with a special grinding and polishing machine → grinding → check whether the size is correct. Reinforce the back. 4. Use a hard diamond water mill to grind the chamfering, first 50#, then 150#, then 300 #; When grinding, use 500# water mill first, and then use 1000#, 2000# and 3000# water mills to grind in turn. Note that the diamond water mill must be hard and must be emphasized with the supplier. The size of the water mill can be divided into 3 inches and 4 inches, which can be determined according to the use requirements. 5. The connection must be made with a 45-degree bevel. 6. Cutting must use a hard diamond saw blade with high hardness and large cutting volume. When the saw blade is cooled with water, the cutting speed should be above 6000 rpm. The saw blade with insufficient emery content will crack the Shi Ying slate due to high-speed impact due to insufficient cutting sales. This saw blade is not durable. The used high-hardness diamond saw blade must have a sand outlet or a sand hole, so as to avoid that the broken quartz sand cannot be discharged in time, resulting in local heating and cracking of the Shi Ying plate during processing. 7. Open the furnace hole 1. According to the design requirements, determine the center position of the basin hole, and the distance from the edge of the furnace hole to the back water stop is not less than 70mm；; 2. When opening the furnace hole, you must first drill holes in the four corners of the furnace hole (the drill bit must be a high-hardness diamond bit, which is available in the stone processing tool shop in Yunfu), and then slowly and evenly cut it into squares with a wire cutting machine. When cutting, you can't cut through the plate at one time, but cut it in two steps, the first step is to cut through the plate thickness 1/3, and the second step is to cut through the plate to prevent cracking. 3. When opening the furnace hole, there should be a backing plate at the bottom of the Shi Ying slate, which can't be completely suspended, and the bearing is important and even, so as to prevent cracking due to uneven stress during the furnace opening. 4. After the furnace hole is cut into squares, the four corners of the furnace hole are polished into arc angles with an angle grinder, the arc radius is not less than r 10 mm, the back surfaces of the four corners of the furnace hole are thickened with small plates of about 120× 120mm, and then they are polished into corresponding arcs with an angle grinder, and the four sides are thickened with Shi Ying slate with a width greater than 30 mm ... (1) marble glue. Yunfu is available for sale and is the most commonly used. The specific use must be carried out in accordance with the requirements of the instruction manual. (2) Special adhesive for quartz stone. Quartz stone shall be prepared in the factory, and the barge interface must be dry, oil-free and wax-free. If you are not sure, you should scrub it with acetone or natural water and wait until it is cooled and dried before bonding. The connection port of quartz stone is preferably 45 degrees oblique, and the connection port must be roughened. This glue can be cured in 15 minutes, but it will be completely matched (inlaid) with quartz stone in one week and one month. (3) Special dry glue for quartz stone. The glue prepared and used in quartz stone factory is the same as quartz stone, but the difference between wet and dry is different. (4) Epoxy AB dry-hanging adhesive. Yunfu stone shop sells it, and you can use it according to the instructions when using it. In a word, the processing technology of quartz stone is the same as natural stone, and the processing methods and tools are the same as natural stone. Never transplant the processing technology of general artificial stone to quartz stone.