Introduction: this knot is very easy to tie, but it is difficult to untie. Therefore, it is necessary to avoid using it on some ropes with good texture, and it is not good to use it on ropes that will be tightened, because it is difficult to untie after tightening.

Usage: Connect two ropes together, usually hard and soft.

Method:

1. Alternately juxtapose the front ends of two ropes, so that one rope in the base can tie a knot like the other rope;

2. Tie a knot on the other side;

3. Tighten the ropes at both ends.

Twenty-six. Double fisherman's knot

It is most suitable for connecting rope loops or ropes that are often placed (not often untied), because it is not easy to untie after bearing.

Method:

1. Increase the winding times of fisherman's knot again and tie it;

2. The other side is also knotted;

3. Tighten the ropes at both ends.

Twenty-seven Rachel (female name)

Often used to tie shoelaces. Just pull the end of the rope on one side and it will loosen.

Method:

Just pull the rope end of A and it will untie the knot.

28.bow

The most commonly used knot when tying shoelaces is generally called bow; It appears quite frequently in daily life. As long as you pull the ends of the rope, the knot will automatically untie. The finished shape is very beautiful and is often used as decoration.

Method:

Twenty-nine surgical knot

Surgical knot, as its name implies, is a knot tied by a doctor when sewing a wound during surgery. Surgical knot can also be used to connect two ropes. Its knot is stronger than a flat knot, so you don't have to worry about whether it will spread. It is suitable for using thin and smooth ropes. At the same time, the surgical knot is very suitable for binding soft and bulky items such as duck down quilts and down jackets. But the disadvantage is that it is not easy to untie. The characteristic of surgical knot is to add one more turn to the initial winding of flat knot, but if one more turn is added to the second winding, not only the endurance is increased, but also the knot becomes neat and beautiful.

Method:

1. Cross-wind two rope ends twice;

2. Tie a knot at the top like a flat knot; Pay special attention not to go in the wrong direction;

3. Tighten the knot;

4. The knot in the second step can be wound one more time, so that the knot will become neat and beautiful;

5. it's done.

Thirty. Half knot

The function of the half knot is to tie the rope to other articles, but it is not suitable for tying square and angular articles, and can only be used for cylindrical articles. However, due to the low endurance of the semi-knot, it will disperse when pulled slightly, so it is rarely used alone. The function of semi-knot is to serve as the basic knot of many complex knots. In addition, it can be added to the ends of other knots after completion to make the whole knot stronger.

Method:

1. Put the rope on the cylinder;

2. Wrap the rope head around the rope once;

3. Tighten it through the rope head in the direction of arrow.

Thirty-one. Double half knot

Although the semi-knot itself cannot stand the pull of external force, the combined strength of the two semi-knots is amazing; That's a double half knot. Even if the rope is pulled to the root of the pole, the double half knot will not be loosened and can be easily untied. When tying things with a rope, the simplicity and certainty of the double half knot is the best choice among all knots, which has a wide range of applications, especially in outdoor activities such as camping. However, the double half knot seems easy, and once you want to fight, you often can't succeed immediately; This is probably the only drawback of the double half knot! As for the double knot, its shape is roughly similar to the double knot on the back page.

Method:

1. Make a half knot;

2. Then bypass the main rope and tie a half knot at the end;

3. Tighten the knot hard to complete;

4. it's done.

Thirty-two Tie a knot

After tying one and a half knots, the remaining rope ends are wound on the rope loop for two or three times, and the knots are wooden knots; Some people also call it a woodcutter's knot or a countryman's knot. In addition, in Japan, people call it a bow tie; Just like the name, its function is suitable for setting up a tent, tying a hammock on a tree or tying a rope to dry things. The advantage of tying a wooden knot is that it is simple and firm. Even if you pull hard, you don't have to worry that the knot will spread. Having said that, tying a wooden knot is not a perfect knot, so tying a wooden knot is not a good choice for items that need to be considered for safety. When using the bow tie, you can add a semi-buckle knot to strengthen protection after completion, which is suitable for carrying slender objects.

Method:

1. Make a half knot first;

2. As shown in the circle, wrap the remaining rope head around the rope loop for two or three times and then tighten it.

Thirty-three Hook knot

When you want to tie the rope of a tent or canopy to a wooden nail, the hook knot is the most suitable knot. Hook knot is also one of the changes of semi-knot, which is characterized by adjusting the length of the rope by moving the knot. In addition, it is not only easy to complete and disassemble, but also very firm. In addition to setting up tents and awnings, even hooks are very suitable knots if you want to keep the rope extremely tight. Since the emergence of new tents such as telescopic tents, hooks seem to be used less; But just in case, we should learn how to play it

Method:

1. Make a half knot first;

2. Tie another half knot a little further from the half knot;

3. Wrap the rope head around once;

4. Finally, tie a half knot and fix it;

5. Tighten the knot forcibly, and adjust the length with knots A and B;

6. When it is difficult to adjust, you can omit the half knot of Part B, and it is just as well to adjust Part A. ..

Thirty-four Double knot

Introduction: The beginning and end of other knots.

Usage: usually suitable for articles with equal stress at both ends, and suitable for horizontal stretching.

Features: extremely safe, however, if only one end of the rope is forced, the double knot may be thrown off or loosened.

Method:

Method ①: A common method of playing, which is formed by winding a rope around an object.

1. Wrap the rope around the object;

2. Make another circle from above;

3. Tighten both ends of the rope;

4. Just tie a half knot at last, even if you pull the rope hard in the direction of the arrow, you don't have to worry about the knot coming apart.

Method 2: Make two loops and overlap them on the object to complete the double knot. This method is very quick and convenient when you want to wrap the rope around the object, and you can tie the knot from the middle of the rope.

1. Do two loops;

2. Overlap the right loop on the left loop;

3. Put it directly on the object;

4. it's done.

Method 3: When the position of the object is in a horizontal swing state, or when the force is exerted from below, you can use this play to complete the winding. If only one side bears the load, it is safer to add half buckle.

In the process of climbing the snow-capped mountains, in order to prevent falling, when climbing in groups, if it is a group of three people, I am used to using such knots for the middle people.

Thirty-five Shuangshuangjie

In order to make the knot stronger, after the double knot is tied, make a circle and it will be a double knot. Usually used when the rope must be placed on an object for a long time. The commonly used play is the first play, and if a rope loop is needed, it can be done by the second method.

Method ①:

Method 2:

Thirty-six. Sanzujie

Introduction: the function is the same as that of double knot, but it is stronger.

Usage: Suitable for vertical traction.

Method:

The purpose of three groups of knots is to tie the rope to the object, which is characterized by winding the rope once more on the way of tying the double knot. Once both ends of the rope are tightened in the opposite direction at the same time, it becomes very firm.

Thirty-seven Grab the knot (Prussian knot)

The biggest feature is that it is easy to knot. Pay attention to keep the load balance at both ends of the rope when using. Can be used to hang items or bind with other knots. In addition, grasping knots is the basis of weaving knots, and weaving booths, hanging baskets, handbags and so on are inseparable from grasping knots.

Method:

It has an effective braking effect in the case of sudden pressure.

Thirty-eight Water knot

Used to connect two ropes with the same thickness, a simple and strong knot. In the world of rock climbing, this is called ring consolidation. Connecting the two ends of the rope in this way can make a sling. This kind of knot is mainly suitable for connecting flat belts. The play is very simple. After tying a knot at the front end of one rope, another rope passes through the circle of the previous rope and is next to the knot. Although the knot can be made small and beautiful, it should be noted that sometimes it will be loose, so the end of the rope must be left with a length of four to five centimeters, and the knot must be firmly tied.

Method:

1. Tie a knot at the end of the rope, leaving enough length at the end;

2. Start from the end of the previous rope and cross the other rope in the opposite direction of the knot;

3. After the rope passes through;

4. After leaving a certain length at the ends of the two ropes, tie them into a knot.

Thirty-nine Double ring junction

Can be used with hooks.

Method:

Forty. Mixed junction

Used for connection between ropes with different diameters.

Method:

Forty-one Staggered knot

Also known as fisherman's knot, sailor's knot, tight knot and wild silkworm knot. Used for connection between ropes with the same diameter.

Method:

Forty-two Lever knot

A lever knot is a knot that ties a rope to an accessory. It can be used to connect ropes between trees, and it can also be used to tie tent ropes when setting up tents, just like double half knots and wooden knots. In addition, when the rope is easy to slip or the rope head is too short to apply force, you can tie a knot on the rope and use the lever knot as a handle; A stick handle is usually added after the project is completed. The disadvantage of lever knot is that if the knot is not tightened hard, it will be in danger of automatic loosening. However, because it is very easy to play and disassemble, even with some minor shortcomings, it is still widely used and can be called an indispensable knot in camping activities.

Method 1: Put the rope directly on the post.

1. After winding the rope around the post, wind the rope head around the rope;

2. Twist the rope loop into a small rope loop;

3. Thread the rope end through the rope loop and tie the knot.

Method 2: Play with the handle on the rope.

1. Tie a knot on the rope as shown;

2. Insert the rod-shaped object and tighten it.

Forty-three Back traction

As we all know, the back knot uses the middle part of the rope as a loop. It was originally used as a prop to tame wild horses. When pulling a heavy object with a rope, people often make this knot into several rope loops and then wrap the rope around their wrists or shoulders to work; Therefore, the back traction knot is also called the manpower knot. In addition, in ancient times, when the army moved and towed artillery, it also used the back tie to achieve its goal, so it was also called gun tie. However, the above-mentioned uses have gradually disappeared in recent years. Now its function is to hang some small things with ropes during camping activities. Although it is a simple knot, if it is used too much or the load is too heavy, the knot will loosen and the circle will become bigger.

Method:

1. Make a circle in the middle part of the rope, and then pull down Part A;

2. Make the rope into the approximate shape as shown in the figure, which is exactly the shape shown in the last play 2 of the lever knot. Then pull out part b in the direction of arrow;

3. Stretch forming;

4. Tighten to complete the back knot.

44. Intermediate knot

Like the strap knot, it is a knot with a ring in the middle of the rope; But in terms of firmness and safety, the middle knot is better than the back knot, and there is almost no need to worry about whether it will be loose. Besides, it's easy to untie. The middle knot, as its name implies, is often used on people who are tied in the middle when climbing mountains; At this time, make a big rope trap on the middleman. At the same time, you can also use the middle knot on a rope to make several small rope loops for hanging portable lamps and the like, which are widely used.

Method:

Method ①:

1. Make an 8-shaped circle with the middle part of the rope, and then pull up Part A to make the shape shown in Figure 2;

2. Pull Part A toward the head;

3. Tension is completed.

Method 2: Although the shape of the knot is a little different, it can still be regarded as an intermediate knot.

1. After the middle part of the rope is folded in half, pull the folded part upward;

2. As shown in the figure, let the two cycles cross;

3. Tension is completed.

45. shorten the knot

Usage: shorten the long rope to avoid cutting it short because it is too long, and you can also use this method to strengthen the protection of the easily worn part of the rope.

Features: If the rope is too loose, the knot will easily loosen and lose its function.

Method ①: Fold the rope twice, and then fix it at both ends with half knots.

Method 2: Make three circles side by side, pass through the left and right circles and pull out the middle circle.

Methods of strengthening and shortening knots: when strengthening, use double knots as shown in the figure or insert rod-shaped objects in the left and right rope rings.

Forty-six Chair knot

The main purpose is to lift the sick and wounded from a height to the ground. This knot is tied to the rope body, and both ends of the rope are controlled by people at high places and on the ground respectively.

Method:

47. Central ring

Can be used to support or pull people out of cracks in ice gaps or other places that are difficult to climb out. When making, the rope needs double strands, and the two rings made are neither too tight nor squeezed. Use one around the hips and the other around the upper body, just like a work hanger.

Method:

1. Bend the double-stranded rope into a ring and pass the live end through the ring.

2. Put the movable end down (a), then put it on the double-layer ring (b), gently move it behind the fixed part (c), and pull the large double-layer ring to tighten it (d).

It's like a triple collar. You need to practice it before using it. You will find that the ring has many uses. When decorating a house or boat, you can use this ring at both ends to support the suspended platform. If there are wooden poles at every corner of the platform, grooves can be made on the wooden poles to prevent the rope from slipping.

Forty-eight Climb a knot

This knot has an anti-slip ring, which can be made in the middle of the rope, but not at the end of the rope. A rope can be tied with several climbing knots, which can be put on the human body, pulled or lifted. When climbing a mountain, it is quite convenient to bring a rope with a climbing knot. You can put your hands and feet on the ring to support your body. When you feel tired, you can rest on it for a while.

Method:

1. Over the rope;

2. Fold the rope into a ring;

3. Twist a small ring again;

4. Pass the small ring through the original ring;

5. Pull gently to fix the knot and tighten it carefully.

Note: If you accidentally make a mistake when tying a knot, it may become a slip ring. If the ring is not twisted as shown in Figure 3, you can find other ways to tie the knot. The firmness of the ring is not affected by the twisting mode, nor by whether the twisting changes.

49. rope ladder

Tie some climbing knots on the rope as many as you need, and then you can make a simple rope ladder. You can also use rungs, solid bars or the wreckage of planes and vehicles after an accident.

Method:

Use two ropes, or a longer rope, to complete the double use. In the ropes on both sides, the interval of climbing knots should be equal. When making a rope ladder, put the stick through the corresponding ring. When making climbing knots, attention should be paid to making the rings tighten the sticks, and the spacing between the sticks on the rope ladder should be reasonable. To be on the safe side, try to see if each knot is firm before use.

Fifty. lasso

This is another lasso knot, which can slide freely, but this knot has obvious rings and is suitable for throwing and catching things, so it is a lasso.