Current location - Education and Training Encyclopedia - Resume - Seeking literature and machinery.
Seeking literature and machinery.
1, edited by Yang Zhanyao. Schematic diagram of typical structure of injection mold [M]. Chemical Industry Press. 2005.5

2. Editor of the Editorial Board of Education Series of Mold Design and Manufacturing Technology. Mold structure design [M].

Machinery Industry Press. 2003. 10

3. Editor-in-Chief Qian Quansen. Plastic molding technology and mold design [M]. Shandong Science and Technology Press.2004.8+00

4. Shuxun Wang Zhu Yalin Meiling Long Guo Liang. Injection mold design [M].

South China University of Technology Press .2005.5

5. Editor of the Editorial Board of Mould Practical Technology Series. Design, manufacture and application of plastic mould [M].

Machinery Industry Press .2002.7

6. Feng, Han, Yin Zhenhai and Jiang. Concise Handbook of Mold Design and Manufacture [M].

Shanghai Science and Technology Press.

7. Editor-in-Chief Zhang Guoqiang. Injection mold design and production application [M]. Chemical Industry Press. 2005.2.

8. Editor-in-Chief Lu Ning. Practical injection mold design [M]. China Light Industry Press. 1997.5.

9. Pang Zugao, editor-in-chief. Plastic molding foundation and mold design [M]. Chongqing University Press .2004.6

10, edited by Chan Verner. Course of plastic injection mold engineering [M]. Beijing hope electronic publishing house.

1 1, edited by Shi. Guide to mold design [M]. Machinery Industry Press .2003.8

12, edited by Shuxun Wang. Practical technology of injection mold design and manufacture. South China University of Technology Press. 1996.4438+0.

13, Zhang yinlang. Concise Manual for Calculation of Plastic Injection Mould [M]. Sinopec Press. 1995

14, Ma Jinjun. Plastic mold design (revised edition) [M]. China Science and Technology Press. 1994.

Tang Zhiyu, 15. Mold designer Guide to Plastics [M]. National Defense Industry Press. 1999.

Zhang 16. Injection mold design [M]. Xi 'an Northwestern Polytechnical University Press. 1995

-

[1] Danggenmao Luo Zhibin Li Jiren. Mold design and manufacturing [M]. Xi 'an: xidian university Publishing House, 1995.

[2] Writing group of plastic mold design manual. Handbook of Plastic Mold Design-Third Edition [M]. Beijing: Machinery Industry Press, August 2000.

Yang Zhanyao. Structure and design of plastic injection mould [M]. Beijing: Tsinghua University Publishing House, 2004.438+00.

[4] Xu Fayue. Handbook of Practical Mold Design and Manufacture [M]. Beijing: Machinery Industry Press, 2000.6438+00.

[5] Tan Songxue. Pro/enginger 200 1 Basic Chinese Course [M]. Beijing: People's Posts and Telecommunications Publishing House, June 2002.

Lin Qing 'an. Pro/enginger 200 1 mold design [M]. Beijing: Tsinghua University Publishing House, 2003.

[7] Editor-in-Chief of China Standards Publishing House. China National Standards Compilation 39GB 4112 ~ 4197 [s]. Beijing: China Standards Publishing House, 1989.537-566.

[8] Writing group of plastic mold design manual. Handbook of plastic mold design [C]. Beijing: Machinery Industry Press, 1982

Wang Xu. Atlas of Plastic Mould Structure [M]. Beijing: Machinery Industry Press, 1994.

Shuxun Wang. Practical technology of injection mold design and manufacturing [M]. Guangzhou: South China University of Technology Press, 1996.

[10] Editorial Board of Plastic Mold Design Manual (Software Edition). Plastic mold design manual (software board) V 1.0 [CP/DK]. Beijing: Machinery Industry Press.

[1 1] Jia,. Practical injection mold design manual [M]. Beijing: China Light Industry Press, 2000.

[12] Song Yuheng. Practical handbook of plastic injection mold design [M]. Beijing: Aviation Industry Press, 1994.

[13] Shi Anfu Palace Cloud Table. Handbook of engineering plastics [M]. Shanghai: Science and Technology Press, 200 1.5

[14] Junyi Technology, etc. Pro/ENGINGEER plastic mould design [M]. Beijing: People's Posts and Telecommunications Publishing House, February 2006.

[15] Wu peinian, Jenny Wong. Descriptive geometry and mechanical drawing [M]. Harbin: Harbin Institute of Technology Press, 1993.

Liao. Interchangeability and Basis of Measurement Technology-Third Edition [M]. Beijing: China Metrology Publishing House, 2002. 1.

[17] Hong Jiadi, Li Ming, Huang Xingyuan. Guide to mechanical design [M]. Nanchang: Jiangxi University Press, 200 1

-

[1] Compilation of plastic mold design manual. Handbook of plastic mold design. Beijing: Machinery Industry Press 1997.5.

[2] Chengdu University of Science and Technology and other units. Plastic mold. Beijing: China Light Industry Press, 1994.

[3] edited by Wang Xiaopei. A concise handbook of plastic molding technology and molds. Beijing: Machinery Industry Press, 1995.

[4] Li Jun. Proficient in Pro/ENGINEER Chinese Wildfire Edition. Beijing: China Youth Publishing House, 2004 [5] Yang Feng. Mold design. Beijing: People's Posts and Telecommunications Publishing House, 2003.

[6] Xu Hao. Handbook of mechanical design. Beijing: Machinery Industry Press, 1993.

[7] edited by Huang Hong. Plastic molding and molding. Beijing: Chemical Industry Press, 2004.

[8] Shen Kaizhi. Plastic mold. Beijing: China Light Industry Press, 2002.

[9] Xu Peixian. Plastic products and mold design. Beijing: China Light Industry Press, 200 1.

[10] edited by Wang Boping. Interchangeability and measurement technology. Beijing: Machinery Industry Press, 2002.

[1 1] Shi Guangyuan and other mechanical drawings. Beijing: Machinery Industry Press, 2000.

[12] edited by Li Dequn. Plastic molding technology and mold design. Beijing: Machinery Industry Press, 1994.

[13] Jiang et al. Typical structure of injection mold 100 cases. Beijing: China Light Industry Press, 2000.

[14] Editor of the Editorial Board of Mould Practical Technology Series. Design, manufacture and application of plastic mould. Beijing: Machinery Industry Press, 2002.