First, the router is initialized and reset, and factory settings are restored (very important). Then connect the computer network card to the LAN port of the router with a network cable, and the router is turned on. Computer network card settings192 5438+068.438+0.2;
Double-click IE browser on the computer, enter the IP address of the router default setting page in the address bar: 192. 168. 1, and press enter;
Enter the default user name: admin and default password: admin; Click OK.
1, set dial-up account:
Click the installation wizard in the left column, and then click Next;
Click ADSL Virtual Dialing (PPPOE), and then click Next;
Enter the broadband account number and password, and click Next;
2. Set the wireless wifi password:
There is also an option in the wireless settings on the left. There is an ssid, which is your wireless account. After setting, there is also a password setting. The password should be as complex as possible, preferably a combination of alphanumeric symbols.
3. Set the login password
Change the default administrator and administrator login password to prevent someone from modifying the router after cracking the password and destroying the network.
Click Save and Restart to complete the operation.
Can the network port of the dormitory be connected with a wireless router? If there is no limit, it is also possible.
Can you, just try it yourself. . .
How to connect the wireless router in the dormitory of Zhejiang University? Even the router needs a universal line, which means that the library has a router connected to the bus, and it can only access the Internet after receiving the signal. If you don't open the internet in the dormitory, you can't get up. Actually, we can pry open China Telecom's box. We all do this, just use scissors, then buy a switch, connect the cable, buy a network cable, connect the computer under the desk and access the intranet 665438+.
How to set up a wireless route to connect wireless routes without network cables? This is the setting of the wireless bridge.
:jingyan . Baidu ./article/63 ABC 44 a 9 b 8 b 056 1f 17 EAC。
Look at the introduction here
How to set up wireless routing in dormitory campus network If you want to connect by wireless routing, your computer must be equipped with a wireless network card to connect with it. Of course, wireless routing also has wired ports, and it is also possible for you to connect with the computer network card with a cable.
The wireless router used in the dormitory, but I am far away. The signal is too bad. How to connect a wireless router with a network cable for signal transmission? But it also has a wired interface on the back. You can buy a network cable long enough to connect the crystal heads at both ends and wire it according to your dormitory. One end of the network cable is connected to the wired interface on the back of the wireless router, and the other end is connected to your computer, so that the network cable is connected.
Network cable connecting wireless routing Now many home routers have dialing function! If your landlord's router has dialing function, you can ask the landlord's router to dial, and both the landlord's computer and your computer access the Internet through the router agent. Judging from the situation you described, it is now networked like this.
The following settings are set in the computer: local connection/properties/internal protocol (tcp/ip)/ properties, just check the automatically obtained ip address.
Plug the network cable of the landlord router into the second port of the wireless router (usually the first port is WAN). Borrow a network cable to connect the third port of the wireless router to the computer, access the wireless router, and set the wireless password. Unplug the borrowed network cable and you can surf the Internet wirelessly.
Company intranet, connect the wireless route and plug the network cable into the routing lan port. At the same time, turn off the wireless routing DHCP service. Client IP is set to192.168.9.x. Please consult your network access provider for DNS settings.
The network cable is connected to the wireless route, and then the network cable of the wireless route is connected to the WAN port of the router. Set the router correctly (for example, Internet access mode, Internet access account, password, etc.). );
Pull the network cable from the LAN port of the router to the computer, or connect the computer with WIFI signal.
Wireless Routing in Dormitory Recently, if the network connection to the dormitory is slow, you should first open the computer LAN firewall (security software is usually turned off by default) and try to plug in the network cable to connect to the network. If it is good, someone will use LAN management tools. If it is not good, the next LAN management tool will limit the speed of others (not recommended, choose carefully! Recommended tool p2p)