Press the red button on the left again.
Then press the machine power switch.
Open the door below.
Check the temperature of the machine, and do not proceed to the next operation until the temperature rises to 35 degrees.
After the temperature rises, close the door and start pressing ink. Before pressing ink, prepare two pieces of cloth, folded into 1/3 size, for wiping the ink nozzle. Before pressing ink, turn on the ink switch and turn the even switch from vertical to horizontal, as shown in the figure.
Push the drawer under the ink.
Press and hold the two buttons of color ink pressing and white ink pressing at the same time to observe the ink flowing out. When you silently count to 10, release the white ink button, count to 7, release the color button, and quickly wipe the nozzle from left to right. You need to fold the cloth from the innermost place when you wipe it. After all the colors are wiped, take a cloth and wipe it again in turn, and try to clean the nozzle.
After wiping the nozzle, check whether the ink is pressed successfully, and print colored strips on white paper. First, find out where to draw the color bar, measure the horizontal distance from the origin to the color bar with a ruler, and then open the printing software on the computer.
Point setting, enter the measured value behind the white edge of X.
Adjust the height of the z axis. Click the Z axis, and the height of the machine is +0.7 of the printed material, so you can enter 0.7mm, click the positioning height, save and exit, or enter 2.7mm (the height of ordinary glass in our company is 2mm), click the positioning height, and save and exit.
Move the machine and press the forward button on the machine.
Make the midpoint position of the machine consistent with the midpoint position of the ribbon to be printed in the vertical direction.
The red dot position is the midpoint position of the machine.
Press the adsorption button.
Click Detect on the computer printing software, and then click Start Printing.
If the printed color stripes are seriously broken (more than 3 broken lines), it is necessary to re-ink.
The color bar printing is completed, the machine is turned on successfully, and it can be printed.
Because the drawing steps are complicated, I wrote another article, click here to see: image processing method of UV printer. Assuming that all the pictures are ready, find the corresponding print file according to the contents of the drawings before sending them, and find this file in the folder by comparing the customer name, glass size and load to be printed on the drawings.
Different products upload and print files in different ways.
0 1. Transparent direct cut glass
After finding the file to print, open the PM software.
Drag the file to be printed into this software, and the display will hang.
Transparent glass generally has two files, one is printed in white, and the end of the file name is XXKG spot color. Drag to the software and double-click this file, and the F point is reversed.
Click Color Management to see if the output configuration is CaYi.
Click on the location as shown.
Check whether it is a spot color 1. Spot color is nothing else. Spot color 1 is Bai Mo.
Click Send.
Wait for him to upload.
Another file, the end of the file name is XX background spot color, the operation is the same as above. You need to press F to reverse the car, and then
Point layout preview
Select a single page preview to see if there are any colors other than blue and red in the content to be printed.
If there is no special color, the color management is set to CaYi, and if there is special color, the color management is set to Korea.
After that, the spot color is 1, and all others are changed to none (plus Bai Mo), and then sent.
Sometimes blue files will appear. At this time, the color management of blue files and background files should be selected from Korea. The blue file should be reversed, and then all the spot colors of 1-4 should be changed to none, so as to make the blue darker and print it without Bai Mo.
If there is no background color file in this file and the end of the file name is black, then this file needs to be reversed, and the spot color 1-4 is none.
After uploading the picture, place the glass near the origin.
Click adsorption.
Spray some acrylic paint on the glass, wipe it with a cloth, wipe it several times, and dry the water as much as possible, otherwise the printed text will be unclear.
In the printing software, set the -X white edge and enter 0 after the y white edge.
Point to the Z axis, enter a height of 2.7, locate the height, save and exit.
Confirm the Z-axis height again under the software.
Click the file, find the PP output file in disk F, and click the plus sign in front to update.
Find the uploaded file and double-click on the right.
Click Print again, right-click the file to be printed, and Print-Start printing.
If you need to print multiple pieces of glass, for example, the size of glass is 180x330 (direct cutting), you need to right-click File-Print Settings, click Print in the sun, enter the number of printed sheets after the horizontal number, and enter 0.4 at the horizontal distance.
If it is 180x330 glass with circular arc, the continuous drying interval is set to 0.2.
02. Brown direct cut glass
After finding the file to be printed, open the PM software, drag the file to be printed into this software, and the display will be suspended.
Generally, there is only one file for directly cutting brown glass. The end of the file name is XXKG spot color, and the front is printed with tawny glass. Double-click the suspended file without inverting it.
Point layout preview
Select a single page preview to see if there are any colors other than blue and red in the content to be printed.
If there is no special color, the color management is set to CaYi.
If there are special colors, then the color management should be set to Korea.
The point is as shown in the figure.
Spot color 1 is followed by spot color (Bai Mo), and spot color (varnish) is followed by spot color 2. Spot color 2 and spot color 3 are not.
Sometimes there are blue files. At this point, you should select the blue file and another file for color management. After the blue file hangs, double-click it without reversing it. Do not select spot color 1, and do not add Bai Mo. Spot color 2 is a spot color, you need to add varnish. Spot colors 2 and 3 are not.
Send it later, when he finishes.
After uploading the picture, put the glass close to the origin, click Adsorption, spray acrylic coating on the glass, and dry it with a cloth.
Set the -X white edge in the printing software, enter 0 behind the Y white edge, point the Z axis, enter the height of 2.7, locate the height, save and exit, and reconfirm the Z axis height at the bottom of the software. Click file to find the PP output file of F disk, click the plus sign in front to update, find the uploaded file, and right-click to add and print.
Click Print again, right-click the file to be printed, and start printing.
If you need to print multiple sheets of glass, for example, the glass size is 180x330, you need to right-click File-Print Settings, click Print in the Sun, enter the number of sheets to be printed after the horizontal number, and enter the horizontal distance of 0.3.
If the glass size is small, the lateral spacing can be reduced to, for example, 0.2.
04 transparent stepped glass
After finding the file to be printed, open the PM software, drag the file to be printed into this software, and the display will be suspended.
Transparent glass generally has two files, one is printed in white, and the end of the file name is XXKG spot color. Drag to the software and double-click this file, and the F point is reversed.
Select the spot color (plus Bai Mo) after the spot color 1.
Another file, the end of the file name is XX background spot color, the operation is the same as above. You need to press F to reverse the car, and then
Point layout preview
Select a single page preview to see if there are any colors other than blue and red in the content to be printed.
If there is no special color, the color management is set to CaYi, and if there is special color, the color management is set to Korea.
After that, the spot color is 1, and all others are changed to none (plus Bai Mo), and then sent.
Sometimes blue files will appear. At this time, the color management of blue files and background files should be selected from Korea. The blue file should be reversed, and then all the spot colors of 1-4 should be changed to none, so as to make the blue darker and print it without Bai Mo.
If there is no background color file in this file and the end of the file name is black, then this file needs to be reversed, and the spot color 1-4 is none.
After uploading the picture, take a right-angle steel ruler and put it on the origin.
Place the glass step near the steel ruler, press and absorb, spray acrylic paint on the glass, and dry it with a cloth.
If glass with the size of 170x 175 is used, a special steel plate is used instead of a right-angle steel ruler.
In the printing software, set the -X white edge and enter 17.8 after the y white edge.
Point to the Z axis, enter a height of 5.7, locate the height, save and exit.
Confirm the Z-axis height again under the software.
Click file to find the PP output file of F disk, click the plus sign in front to update, find the uploaded file, and right-click to add and print.
Click Print again, right-click the file to be printed, and start printing.
If you need to print multiple sheets of glass, you need to right-click File-Print Settings, click Print, and enter the number of sheets to be printed after the horizontal number. The value entered in the horizontal distance depends on the distance between the glasses. If you type 100x240 glass, enter 10.5.
If you type 170x 175 glass, enter 16.
05 brown stepped glass
After finding the file to be printed, open the PM software, drag the file to be printed into this software, and the display will be suspended.
Generally, there is only one file for brown glass, and the end of the file name is XXKG spot color. The front is printed with brown glass. Double-click the suspended file without inverting it.
Point layout preview
Select a single page preview to see if there are any colors other than blue and red in the content to be printed.
If there is no special color, the color management is set to CaYi, and if there is special color, the color management is set to Korea.
After that, spot color 1 is followed by spot color (with Bai Mo), and spot color 2 is followed by spot color (with varnish).
Sometimes there are blue files. At this time, the color management of the blue file and another file should be Korean. Double-click after hanging, without reversing. Spot color 1 is none, without Bai Mo. Spot color 2 should be followed by spot color and varnish. Spot colors 3 and 4 are not.
After uploading the picture, put the glass close to the origin, click Adsorption, spray acrylic coating on the glass, and dry it with a cloth.
Set the -X white edge in the printing software, and the value behind the Y white edge is the size outside the steps of the dark brown glass. If the glass is 100x240 (without arc), enter 7.5 for x and 7.5 for y.
Point to the Z axis, enter a height of 5.7, locate the height, save and exit. If it is 100x240 circular-arc glass, enter x as 5.5 and y as 5.5, and confirm the Z-axis height again at the bottom of the software.
Click File to find the PP output file of disk F, click the minus sign in front to update, find the uploaded file, and right-click to add and print.
Click Print again, right-click the file to be printed, and start printing.
If you need to print multiple pieces of glass, you need to right-click File-Print Settings, click Print, enter the number of printed sheets after the horizontal number, and enter the distance between two pieces of glass in the horizontal distance. If the glass size is 100x240 without arc, you need to enter 14.7.
Too many files are printed. How to delete them? Close this software.
Then go to drive F to find the PP output file, open it and delete the file you want to delete, and then restart the printing software.
Below the rightmost part of the machine, you can open the door, which is where you add ink.