Decoration requirements for training courses in dance standard venues:
Dancing in the Mirror —— Shanghai Hu Mei
The mirrors in the dance studio are usually decorated with mirrors on a solid wall in each classroom. The height is 2-3 meters from the ground and the width is 2-3 meters. Basically covered with dance classrooms.
There is no difference between the mirror in the dance studio and the ordinary mirror, and there are special requirements for installation.
First, the area is large enough, the height is at least 750px higher than that of people, and the width reaches the width of the classroom as much as possible;
Second, the installation is firm and reliable, and there can be no shaking phenomenon; There should be protection in front of the mirror to prevent students from bumping (most of them are put in front of the mirror with suitcases).
Second, the dance handle-Shanghai Hu Mei
Dance bars can be divided into mobile bars and fixed bars (floor-standing: fixed bar, wall-hanging: fixed bar, mobile bar).
1 Mobile handlebar: a handlebar with a high telescopic height and a heavy base.
Gaoji 1m, 2m wide (single handle), with 2-3 handles in each classroom.
2 Fixed handle: 30-35cm away from the wall.
Height: 1m, wide bottom: 3-4m (one low column per meter).
Sanwuge-Shanghai Hu Mei
1, material: solid wood, commonly used maple grain, oak grain, oak grain.
2. Panel: 25mm, 30mm and 35mm thick bottom plate, vertical plate: 16mm, 18mm, 19mm thin plate (fiberboard) with 3mm, 4mm and 5mm back walls.
2. Specification: height: 40- 1250px, 50-60cm, depth: 1 125px, about 55cm, distance of middle partition: 40-50cm, 50- 1500px, kicking.
Common specifications: height 50cm, width 1500px and depth 50cm.
3. Use: When dancers change their dance costumes, they are used to store clothes and shoes.
IV-Audio-Shanghai Hu Mei
It can be equipped with post-stage power amplifier and pre-stage digital effect device, and the power and timbre can be well adjusted, which is suitable for various types of dance scenes and can be connected to a microphone when necessary. Many stage stereos are also very powerful, many of them are active speakers, and the sound quality is not as good as that of the post-amplifier frequency multiplier. I suggest that it is best to install a pure post amplifier to cooperate with the effector. The power can be considered according to the area of the site. The average site can use 400W*2, and the larger site can choose higher power, such as 600W * 2,800W * 2, 1000W*2.
Wu-Qiang-Shanghai and Shanghai and America
White, pink, pink, gray and blue walls and ceilings blend together.
Land-Dance Lighting-Shanghai and Shanghai and America
The white chandelier is in harmony with the decoration of the whole room, which makes people unforgettable.
Dance is based on the rhythmic movements of human body, which constitutes the "rhythm" emphasized in the artistic image of dance. Therefore, the change of dance lighting must have unique "rhythm" characteristics. The lighting mode of dance lighting is different from that of drama, film and television. Because dance is a dynamic art, it emphasizes the changes of limbs in space, including not only lateral flow, but also body movements that change greatly in space, such as rotation and jumping. Therefore, the performance space is much larger than other stage arts, which requires a large area of light distribution, emphasizing the use of side and backlight to better reflect the dancers' curves and body movements. By contrast, dancing limbs. In the use of color, it is mainly set according to the theme and emotion of the characters to be conveyed in the dance works. Because dance pays more attention to freehand brushwork and is very symbolic, the lighting of dance is often exaggerated with large color blocks. To sum up, it constitutes three characteristics of dance lighting: great change, great cloth and great color. Stage wooden floor, non-slip stage floor, stage floor, stage floor.
The characteristics of lighting in dance performance come from dance, an art category with strong comprehensiveness and special expression. Japanese dancer Bang Mei Zheng attaches great importance to the coordination between lighting design and dance creation. He believes that "lighting is very important for dance, which plays an auxiliary role in stage installation or theme presentation, and also affects the size of performance space, making the space more distinctive". Therefore, only music, lighting, clothing, make-up, body and other artistic forms participate in the creation, can jointly inspire and reflect the essence of the work more deeply and accurately. The mechanical cooperation taught by the director is light and color without soul.
Seven-story Dance Floor (Stage Dance)-Hu Mei
There are five types: dance scratch-proof, high elasticity scratch-proof, children dance scratch-proof, adult dance scratch-proof, upper and lower parts scratch-proof, and temporary use. There are several types of high elastic scratch-proof (different contents and different prices) and stage scratch-proof
Ba wood flooring-Shanghai Hu Mei
Material: The panel layer generally adopts maple wood grain, oak grain and oak grain, with a thickness of 20mm, a width of 60m and a length of 300mm to 900mm, with grooves and flanges. It is suitable for the ground construction of indoor sports venues such as basketball court, volleyball court, badminton court and table tennis court.
Note: the floor is not slippery or astringent.
Plastic Floor Construction /PVC Floor Construction/Dance Floor Construction/Flax Floor Construction/Rubber Floor Construction/Dance Floor Construction/Stage Floor Construction/Elastic Floor Construction/Coil Floor Construction /PVC Floor Construction/Dance Plastic Floor, Plastic Floor of Dance Studio, Plastic Floor of Dance Academy, Plastic Floor of Dance School, Plastic Floor of Dance Rehearsal Room/Shanghai Hu Mei Plastic Floor, Plastic Floor of Stage, Plastic Floor of Dance.
One: Self-leveling construction-bottoming
1, absorbent base such as concrete and cement mortar screed-coat should be prepared with multi-purpose interface treatment agent according to the ratio of 1: 1, and then the primer should be sealed.
2. Non-absorbent substrates such as ceramic tiles, terrazzo and marble. It is suggested to use dense interface treatment agent for priming.
3. If the moisture content of the base is too high (> 3%) and construction is needed immediately, epoxy interface treatment agent can be used for priming treatment, but the premise is that the moisture content of the base should not be greater than 8%.
4, interface treatment agent construction should be uniform, no obvious effusion. After the surface of the interface treatment agent is air-dried, the next self-leveling construction can be carried out.
Second: Self-leveling construction-mixing
1. Pour a bag of self-leveling water-cement ratio into a mixing barrel filled with clean water, and stir while pouring.
2. In order to ensure uniform self-leveling mixing, a high-power low-speed electric drill with a special stirrer must be used for mixing.
3. Stir into uniform and non-caking slurry, let it stand for about 3 minutes, and then stir briefly.
4. Water should be added in strict accordance with the water cement ratio (please refer to the corresponding self-leveling instructions). Too little water will affect fluidity. Too much will reduce the strength after curing.
Three: Self-leveling construction-laying
1. Pour the mixed self-leveling mortar on the construction ground, and it will flow by itself to level the ground. If the design thickness is ≤ mm, it needs to be scraped slightly with the help of a special tooth scraper.
2. Then, let the construction personnel put on special spikes, enter the construction site, and gently roll them on the self-leveling surface with special self-leveling deflation rollers to release the air mixed in the stirring to avoid bubble pits and interface height difference.
3. Please close the site immediately after the construction. No walking is allowed within 5 hours. Avoid the impact of heavy objects within 10 hour. After 24 hours, lay the PVC floor.
4. During winter construction, the floor shall be laid after 48-72 hours of self-leveling construction.
5. If it is necessary to finely polish the self-leveling cement, it should be done after the self-leveling cement is completely dried.
Four: Floor paving-pre-paving and cutting
1, whether it is coiled material or block, it should be placed on site for more than 24 hours, so that the material memory can be restored and the temperature is consistent with the construction site.
2. Use a special edger to cut and clean the burr of the coil.
3. When laying blocks, there should be no joint between two pieces of materials.
4, coil laying, two pieces of material should adopt overlapping cutting, generally require overlapping 3 cm. Pay attention to keep the knife cut.
Five: the paving of the floor
1. Choose the glue and rubber roller suitable for PVC floor.
2. After the coil is laid, roll up one end of the coil. Clean the floor and the back of the coil first, and then scrape the glue off the floor.
3. When paving the block, please turn the block from the middle to both sides, and at the same time clean up the ground and the back of the floor and glue it.
4. Different adhesives have different requirements in construction. Please refer to the corresponding product specifications for details.
Six: ground pavement-exhaust and rolling.
1. After the floor is pasted, first push the surface of the floor flat with cork blocks to squeeze out the air.
2, and then use 50, 75 kilograms of steel roller evenly rolling floor, timely repair splicing edge.
3. Excess glue on the floor surface should be wiped off in time.
4, after 24 hours, then slot and welding.
Seven: Floor Paving-Slotting
1. Slotting must be carried out after the glue is completely cured. Use a special slotting machine to slot along the seam. In order to make the welding firm, the weld should not pass through the bottom. It is suggested that the depth of groove should be 2/3 of the floor thickness.
2. At the inoperable end of the sewing machine, please use a manual sewing machine to sew with the same depth and width.
3. Before welding, the residual dust and sundries in the box must be removed.
Eight: Floor Laying-Welding
1. Manual welding gun or automatic welding equipment can be selected for welding.
2, the temperature of the welding torch should be set at about 350 degrees.
3. Squeeze the covered electrode into the groove of the opening at an appropriate welding speed (to ensure that the covered electrode melts).
4. When the covered electrode is in a semi-cooling state, roughly cut off the part of covered electrode that is higher than the ground level with covered electrode level or moon knife.
5. When covered electrode is completely cooled, use covered electrode flat pliers or crescent knife to cut off the remaining protruding part of covered electrode.
Nine: floor cleaning and maintenance
1, PVC series flooring is developed and designed for indoor places and should not be laid and used in outdoor places.
2. Please select the corresponding cleaning agent according to the method recommended by the manufacturer for regular cleaning and maintenance.
3. Avoid dumping high-concentration solvents such as toluene and banana oil, strong acids and strong alkali solutions on the floor surface, and avoid using inappropriate tools and sharp tools to scratch or damage the floor surface.
X: related tools
1. floor treatment: surface humidity tester, surface hardness tester, floor grinder, high-power industrial vacuum cleaner, wool roller, self-leveling mixer, 30l self-leveling mixing barrel, self-leveling tooth scraper, nail shoes and self-leveling inflator.
2. Floor laying: floor edger, cutting machine, 2m steel ruler, glue scraper, steel roller, grooving machine, welding torch, crescent knife, covered electrode leveling instrument and combined marking machine.
Plastic floor is another name for PVC floor. The main component is PVC material, and PVC floor can be made into two kinds, one is homogeneous infiltration, that is, the pattern material from the bottom to the surface is the same. Another kind is elastic, that is, the top layer is pure PVC transparent layer, and the printed layer and foam layer are added below. "Plastic floor" refers to the floor made of PVC material. PVC flooring is widely used in all aspects of family and business because of its rich colors. dance floor
Plastic flooring is a broad term. There are many opinions on the Internet, which should be said to be inaccurate. Plastic floor is a very popular new light floor decoration material in the world today, also known as "light floor material".
It is a very popular product in Europe, America, Asia, Japan and South Korea. Very popular abroad. Since the early 1980s, it has entered the China market and been widely recognized in large and medium-sized cities in China. Widely used, such as indoor homes, hospitals, schools, office buildings, factories, public places, supermarkets, businesses, stadiums and other places. Dance floor glue is another name for the dance floor, which is different from pvc soft effect, with smooth and delicate surface and good flexibility. Moderate elasticity, moderate smoothness, matt plane, which is conducive to buffering the impact force in difficult movements of dance, scratch-proof for ten years and customizable length. And is easy to clean and maintain, and does not change or crack. Stage floor glue
Stage floor, also known as dance floor, is a kind of soft PVC, which is customized according to the characteristics of dance. It has the characteristics of cushioning, non-astringency, non-slip and good flexibility, while ordinary PVC is mostly used for industrial insulation, and its material is hard and rough. The other is sports floor glue, which has a textured surface and high friction, and is suitable for sports competitions. There is a qualitative difference between it and dancing glue. Dance buds are scratched. The colors of the dance floor are colorful (sky blue, dark blue, pink, pink green, national flag red, reduced red, gray, dark gray, medium gray, light gray, cyan gray, towel blue, purple blue, navy blue, orange yellow, dark green, rose red, milky white, silver gray, apricot yellow and black ... It can be made according to the color cards provided by customers. ) Dance plastic floor
1) The dance floor is divided into 5 models: 6 series. Hu Mei Dance Floor Factory can customize it at will!
1 paragraph-for temporary dancing-There are several kinds of scratches (different PVC content, different prices).
Paragraph 2-Special for children dance-High-elastic scratch-free series (adults and children are forbidden to wear high heels, leather shoes and hard-soled shoes to dance in the room. To protect the scratch problem, please wear special shoes for dancing, which can protect your feet from dust and feet.
Paragraph 3-special imported noodles for adult dance-scratch-free series imported noodles (the imported noodles can be customized in length and delivered in 3-4 days, which can bear the weight of adults and will not cause uneven use of products. It is forbidden for adults and children to dance indoors in high heels, leather shoes and hard soled shoes. To prevent scratches, please wear special shoes for dancing.
Paragraph 4-Special for all kinds of dances-Scratch-proof series (leather shoes, high-heeled shoes and hard-soled shoes can be worn to prevent scratches, and the length can be customized. Delivery in 7-9 days, dancing in high heels or leather shoes is not restricted.
Paragraph 5-Stage-specific-Scratch-proof is also called high elastic penetration scratch-proof or scratch-proof (whether it is a competition, a performance or a performance, there is no restriction on the anti-activity of the venue, which is moisture-proof, anti-slip, waterproof, fire-proof, scratch-proof, shrinkage-proof, deformation-proof, sound-proof and wear-resistant. dance floor
Maintenance methods: dance floor glue price, dance classroom glue, scratch-proof dance floor glue and professional dance floor glue.
1) Daily maintenance: clean the ground with a clean and damp mop, and partially clean the heavily polluted ground;
2) Monthly maintenance: It is best to carry out deep waxing treatment and maintenance after dust removal and cleaning of the whole site;
3) Contamination treatment: When ink, food, greasy and other stains are contaminated on the PVC plastic sports floor, the stains should be carefully wiped off immediately, and then the traces should be scrubbed with diluted detergent. When the residual traces of black leather shoes are difficult to remove, you can wet the veil with Haokang special detergent or scrub it with rosin water. Don't pour detergent or rosin water on the floor for cleaning, and wax it for maintenance after scrubbing.
4) Chemical protection: avoid a large amount of water staying on the floor surface for a long time. If water soaks the floor for a long time, it may go deep under the floor, melting the floor glue and losing its cohesive force. It may also cause the floor to be polluted by the protective wax moisture layer on the floor surface, or the pollution may penetrate into the interior of the floor, causing the floor to change color. Ballroom floor
5) Sun protection: Avoid direct glare and prevent discoloration and fading caused by ultraviolet radiation.
Matters needing attention
1) It is forbidden to wear leather shoes, high heels or sports shoes that fade easily; Professional dance floor rubber brand
2) It is forbidden to cut and squeeze, and the surface shall not rub against hard objects to avoid damage or rupture;
3) It is forbidden to use corrosive chemicals such as acid and alkali on the floor, and keep away from fire sources and high temperatures to avoid floor deformation;
4) It is forbidden to drag on the ground when carrying articles, so as not to scratch the floor. Pvc plastic floor glue