I. General requirements

1. Fabrics and accessories are of good quality, meet customer requirements, and the bulk goods are recognized by customers;

2. The style and color matching are accurate;

3. The dimension is within the allowable error range.

4. Excellent workmanship;

5. The products are clean and tidy and sell well.

Two. Appearance requirements

1. The front is straight and the length is even. The front is flat and uniform in width, and the inner placket cannot be longer than the front placket. Those with zipper lips should be smooth, uniform, wrinkle-free and seamless. Zippers don't smoke. Buttons are straight and even, with equal spacing. 2. The lines should be even and straight, and the left and right widths should be the same.

3. Cut straight without stirring.

4. The pocket is square and flat, and the pocket can't be shaved off in the whole lost place.

5. The cover is consistent with the clothes of patch pocket Zhengping Fang, with the same height and size. Height of inner bag. Same size, Zhengping Fang clothes.

6. The collar seam shall be of the same size, the barge head shall be flat, the ends shall be neat, the collar nest shall be round, the collar surface shall be flat, the tightness shall be appropriate, the outer opening shall be straight, and the bottom collar shall not be exposed.

7. The shoulder should be flat, the shoulder seam should be straight, the shoulder width should be consistent, and the flat-fell seam should be symmetrical.

8. The sleeve length, cuff size and width are consistent, and the sleeve tab height and length and width are consistent.

9. The back is flat, the seams are straight, the straps are horizontal and symmetrical, and the tightness is appropriate.

10. The bottom edge should be smooth and flat, the width of rubber root and rib should be consistent, and the rib seam should be striped.

1 1. The lining size and length of each part should be suitable for the fabric, and there should be no sagging and spinning.

12. The patterns of webbing and lace on both sides of the car outside the clothes should be symmetrical.

13. The tampon should be flat, with even line pressing, neat lines and aligned front and back seams.

14. If the fabric has pile (wool), it is necessary to distinguish the direction, and the pile (wool) should be reversed in the same direction.

15. For sleeve sealing style, the edge sealing length shall not exceed 10 cm, and the edge sealing shall be consistent, firm and tidy.

16. It is required that the stripes of the fabric should be aligned accurately.

Three. Comprehensive job requirements

1. The vehicle lines shall be smooth and free from wrinkles or distortions. The double thread part needs to be sewn with a double needle lathe. The bottom line should be uniform, free from needle jumping, floating and continuous.

2. You can't draw lines and marks with pastels, and all marks can't be drawn with pens or ballpoint pens.

3. There should be no color difference, dirt, wire drawing and unrecoverable pinholes on the surface and lining.

4. Computer embroidery, trademarks, pockets, bags, sleeve tab, pleating, corns, hooks, etc. Positioning should be accurate, and positioning holes should not be exposed. 5. Computer embroidery should be clear, the thread ends should be cut off, the backing paper on the back should be trimmed, and the printing should be clear, bottomless and degummed.

6. If required, all corners and covers of the bag should be dated, and the location of the date should be accurate.

7. The zipper shall not fluctuate, and the pull up and down shall be unimpeded.

8. If the lining is light in color, it will develop color. The seams inside should be trimmed neatly and the thread ends should be cleaned. If necessary, insert paper to prevent color from penetrating. 9. If the lining is knitted fabric, the shrinkage of 2 cm should be put in advance.

10. The exposed parts of the hat rope, waist rope and hem rope at both ends should be 10 cm after they are fully opened. If the hat rope, waist rope and hem rope are parked at both ends, they can be laid flat and will not be exposed too much.

1 1. corns, nails, etc. Should be positioned accurately, without deformation, nailed tightly and not loose, especially for varieties with thin fabrics. Once found, it should be checked repeatedly.

12. The snap button has accurate position, good elasticity, no deformation and no rotation.

13. All coils with large stress, such as cloth rings and buckles, should be reinforced with needles. |; g:K.l！ A

14. All nylon belts and braided ropes should be cut by hot cutting or burning, otherwise they will scatter and break (especially when holding hands).

15. The jacket pocket cloth, underarms, windproof cuffs and windproof feet should be fixed. 16. Pants: the waist size shall be strictly controlled within 0.5cm.. 17. Pants: The hidden line of the back wave should be sewn with thick thread, and the bottom of the wave should be reinforced with needles.

Common bad conditions of clothing 1. sew

1, the needle distance is out of tolerance-the needle distance was not adjusted strictly according to the process requirements when sewing.

2. Needle skipping-Discontinuity due to mechanical failure.

3, off-thread-when lifting or dropping the needle, the needle does not return, or the thread floats seriously.

4, needle leakage-due to negligence, leakage, adhesion.

5, hair leakage-refractive burr is not tight, the excavation technology is not enough, and the wrap angle is leaking.

6. Floating line-the soap bubble is too loose, or the line pressing plate is too tight. 7, floating bottom line-the line pressing plate is too loose, or the shuttle is too tight. 8. Sewing back-poor sewing skills, not spitting seam according to process requirements.

9, anti-warping-the face is too tight; Or put your face on it when sewing. 10. Wrinkling-The needle and thread were not replaced according to the thickness of the sewn piece; Or that sew article has a length.

1 1, sewing button-because the technology did not pass the sewing button, the sewing parts did not match.

12. Double-track-check a single open line. After disconnection, the suture is not on the original stitch; After sewing the lower sill of the patch, two stitches were caused when sewing the line. 13, the two lines are not parallel-because of insufficient technology; Or careless operation causes uneven width of double lines.

14, not straight-the seam stop is not straight due to uneven seam position; Technical error detection line bending. 15, uneven clothing-the seams on the surface are not straight and uneven; Inconsistent joints; The upper and lower pieces are not elastic. 16, not square-the corner, bottom edge, swing angle and square collar of the bag are not sewn at 90 degrees.

Not round-the round neck, round pocket angle, round sleeve head and round pendulum of a suit have small corners because of poor sewing technology.

18, asymmetry-due to poor technology or careless operation, errors such as length, height, fat and width occur in the parts that must be symmetrical. 19. Uneven eating potential-Uneven eating potential at the sleeve hill leads to chubby or fine pleats at the sleeve hill. 20. Skew position-there are less than three sleeves, collars and positioning points or the positioning is inaccurate.

2 1. The alignment of the strip and the grid is incorrect-the cutting position is not clearly left when cutting; Or the layout is not strictly aligned with the grid; When sewing, it was accidentally misaligned with the grid.

22. Sew on the top and sew on the bottom-the sewing technique is low or the operation is sloppy, and the sewing line is not always at the hem.

23. The pinhole is exposed-the pinhole at the edge of the cloth is not removed when cutting; Hole removal is not included during rework. 24, the collar angle starts from beans-the sewing technology is low; The cleaning and shearing at the coupling do not meet the requirements; The folding process does not meet the requirements; Not crushed by the collar setting machine.

25. Incorrect location of spare parts-spare parts are not sewn according to sample clothes or process sheets.

26. Mark dislocation-the main mark and washing mark are not sewn according to the requirements of sample clothes or process sheets.

Second, stains

27. Handwriting-illegal use of pens or ballpoint pens to edit the cutting number, work number and inspection number.

28. Oil pollution-the machine leaks oil when sewing; Eat greasy food in the workshop.

29, powder marks-when cutting, powder marks are not removed; When sewing, it is made by drawing and positioning with chalk.

30. Impression-The impression of the cloth head was not cut when cutting. 3 1, dirty mark-the production environment is not clean, and the joints are piled on the ground.

32. Watermark-the stain on the seam of dyed cloth stained with water.

33. Rust-metal buttons, zippers and belt buckles are of poor quality and stick to the seams after rusting.

Third, ironing

34, blanching discoloration-iron temperature is too high, make fabric blanching discoloration (especially chemical fiber fabric).

35. Aurora-there is no steam ironing, and the electric iron has no water cloth to cause local light.

36, dead mark-the hot surface is not smooth, burning out irreversible folds.

37, careless work, large area without overheating.

Fourth, the thread.

38, dead line-not clean after trimming and pruning.

39. live thread-the trimmed thread sticks to the ready-made clothes and will not be removed. 1Wt # @ ` & amp； w

Verb (short for verb) others

40. Cutting and typesetting errors; The sewing direction of small pieces is inconsistent with that of large pieces.

4 1, reverse the cloth surface-the sewing worker will not recognize the front and back, which makes the cloth surface reverse.

42. Cutting pieces are in the same direction-due to cutting and layout errors, symmetrical cutting pieces are cut in one direction. C.ZlB4XS.S{/`

43. Defects are out of tolerance-there are many defects in the fabric, which are not eliminated during the layout, resulting in more than the allowable number of defects in important parts and secondary parts.

44. Incorrect buckle-uneven height of the buckle plate or incorrect buckle.

45, buttonhole askew-buttonhole operator careless operation, did not straighten clothes, resulting in uneven buttonhole, not firm, not straight.

46, color difference-poor quality fabric, bag cut, wrong number, wrong number when sewing, quality color difference will not change.

47. Damage-caused by trimming thread ends, reworking stitches and cleaning water. 8 {hU4uX | Dun

48, degumming-the quality of adhesive lining is not good; There is not enough temperature or pressure and time for bonding.

49, foaming-the quality of adhesive lining is not good; The ironing board is uneven or there is no ironing pad. Y3U/U，S/U9b4？ -You?

50. Glue infiltration-the quality of adhesive lining is not good; The viscose turns yellow, and the iron temperature is too high, which makes the fabric yellow.

5 1, the nailing is not firm-the nailing machine is broken.

52. The button is not tight-it is caused by the quality of the button.

53. Missing work and missing parts-The sewing worker neglects to install various decorative buttons, decorative buttons or missing a part, and the packer forgets to hang tags and spare buttons.