Article 1 This Code is formulated for the purpose of standardizing carpentry work behavior, cultivating safe work habits and ensuring the safety of life and property. Article 2 Anyone who works in this company must abide by this Code. Article 3 Woodworking must take "safety first, prevention first" as the guiding ideology. Article 4 The "Four No Hurts" should be strictly observed during the operation, that is, you should not hurt yourself, others or be hurt by others, and protect yourself from harm. Article 5 Carpenters must receive safety training from our company, and they can only take up their posts if they are qualified. Sixth apprentices and interns must be led and guided by professional and technical personnel, and it is strictly forbidden to work alone. Seventh work, there must be more than two staff in a group, it is forbidden to work alone. Eighth homework, it is forbidden to frolic, slapstick and other unsafe behavior. Ninth aerial work, there must be a special care, and strictly abide by the "high altitude safety operation procedures". Tenth job site should be equipped with fire fighting equipment. Article 1 1 Smoking is strictly prohibited in the work site to prevent fire. Twelfth prohibit the use of power cord insulation rubber damage to power equipment and tools. Thirteenth tools should be put into the toolbox in time when not in use. Article 14 it is forbidden to put nails in your mouth to avoid accidents. Fifteenth when working on the roof with a slope greater than 25, you must fasten your seat belt and safety rope, and at the same time you must be supervised. Article 16 The rigging used for lifting materials must be checked in advance and confirmed to meet the requirements before use. Article 17 No one is allowed to walk or stay in the dangerous area below during lifting and installation. Eighteenth maintenance eaves, must stand on scaffolding, ladders or lifting platform, it is forbidden to lean on the roof. Nineteenth finished products, semi-finished products and wood on the construction site should be neatly stacked and not stored at will. The stacking height shall not exceed1.5m. Article 20 After the operation, all power supplies shall be turned off, and the shavings, sawdust and broken wood on the site must be cleaned up, that is, self-produced, self-sold, daily cleaned and live cleaned. Twenty-first electrical fire, can cut off the power supply in time, should immediately cut off the power supply. If the site can't be cut off, you should immediately contact the personnel on duty at the switch station to cut off the power supply. At the same time, carbon dioxide fire extinguishers, dry powder fire extinguishers, dry yellow sand and other non-conductive fire extinguishing equipment should be used to extinguish the fire, and water is strictly prohibited. Twenty-second fire fighting wood, bamboo and other items, choose the nearest fire fighting equipment, fire fighting people must stand at high altitude. Twenty-third oil fires, you can use fire blankets, foam extinguisher and other equipment to put out the fire. Article 24 Woodworking must comply with the requirements for the use of labor protection articles and the safe use of woodworking tools.

Appendix 1: The use of labor protection articles requires carpenters to wear work clothes and labor protection shoes, fasten buttons and cuffs, and wear personal labor protection articles such as safety helmet, safety rope and safety belt when working at height. It is forbidden to go to work without wearing labor protection articles according to regulations. 1. Labor protection shoes (1) should have anti-skid, anti-smashing and anti-puncture functions; (2) The sole is free of oil stain and serious wear; (3) The vamp has no damage or crack; (4) You should tie your shoelaces at work. 2. Before wearing protective gloves (1), the gloves should be visually inspected. If cracks, damage and serious mildew are found, it is forbidden to use. (2) When in use, the jacket cuff should be put into the glove; (3) Pay attention to prevent sharp objects from puncturing gloves when using. 3. Safety helmet (1) It is forbidden to wear a broken, cracked safety helmet without safety protection signs; (2) The safety helmet shall be used within the effective use period; (3) When wearing, adjust the rear hoop and fasten the chin strap. The safety helmet must be worn correctly and firmly, and cannot shake to prevent it from falling off; (4) A space of 20 ~ 50 mm must be kept between the top of the cap liner and the top of the cap shell, so as to ensure that the cap body has enough buffer space when it is impacted, which is also beneficial to the ventilation between the head and the cap body at ordinary times; (5) It is forbidden to use a helmet with only the chin strap connected to the cap shell, that is, it is forbidden to use a helmet without a buffer layer in the cap; (6) The safety helmet should be checked regularly. If the hat is cracked, dented, cracked or badly worn, it should be replaced immediately. Any helmet that has been hit hard, whether damaged or not, should be scrapped. 4. Seat belt (1) Before using the seat belt, check whether all parts are in good condition, and replace them if they are worn by more than one fifth or the rope is broken; (2) When using, it must be hung high and used low, and it is forbidden to hang low and use high. The hanging point should be firm, not tied with rope, and the hook should be hung on the connecting ring; (3) The protective sleeve shall be kept intact to prevent the lanyard from being worn. If it is found that the protective sleeve is damaged or falls off, a new protective sleeve must be added before use; (4) It is forbidden to extend the seat belt without authorization. If a long rope of more than 3 meters is used, a buffer must be added, and all components are not allowed to be disassembled or modified at will; (5) Pay attention to maintenance and storage after use. Appendix II: Requirements for Safe Use of Woodworking Tools 1. Claw hammer (1) shall not be used when its handle is scarred, perforated and cracked; (2) The handle must be installed firmly and checked for looseness during use. If it is loose, it needs to be tightened, and a chisel should be added to the handle end; (3) It is forbidden to wear gloves when using.

For more information about project/service/procurement bidding, and to improve the winning rate, please click on the bottom of official website Customer Service for free consultation:/#/? source=bdzd