Current location - Education and Training Encyclopedia - Educational institution - What is the safety education plan and document control system on the construction site?
What is the safety education plan and document control system on the construction site?
Talking about the safety control of construction project management The so-called safety control refers to the pre-analysis of unsafe factors existing in the project construction, and taking measures from the technical and management levels to ensure that the construction production is carried out in accordance with the safety production rules and regulations and operating procedures, so that the safety production in the construction process is always under control. As the first person responsible for the safety production of construction projects, how to solve the long-standing problem of the construction site, how to do a good job in the safety control of the construction site, how to improve the construction safety and nip in the bud is an important problem to be solved at present. The author thinks it is necessary to focus on the following three aspects: 1, strengthen the safety education of employees and strengthen the construction safety education of employees. Article 46 of the Construction Law of People's Republic of China (PRC) clearly stipulates that construction enterprises should improve the education and training system of labor production and strengthen the education and training of workers' safety production; Personnel without safety education and training are not allowed to work at their posts. Safe production is the objective need of human production activities and the inevitable trend of the development of human civilization. Safety is one of the basic needs of the National People's Congress. The occurrence of major safety accidents, resulting in personal casualties, not only hurt themselves, bring misfortune to their families, bring losses to enterprises, but also bring greater negative impact to society. At the same time, strengthening safety education can make the safe production of enterprises based on the broad masses and make the party and the country safe in production. Policy, the relevant rules and regulations of enterprise safety production have been effectively implemented and implemented. With the increasing technical content of building construction and the improvement of mechanization of construction equipment, the technical requirements for operators are gradually improving; Especially with the breaking of labor barriers, the proportion of foreign construction workers is increasing because their safety awareness is weak. Low safety operation skills have led to frequent safety accidents, which are obviously on the rise. Therefore, it is particularly important to strengthen the safety education for employees. 2. Strictly control the safety of the construction organization design, adhere to the safety condition review before the project starts, and strictly control the construction organization design, which is an effective guarantee to control the safety from the source. Whether the safety technical measures are included in the construction organization design of building engineering, whether the content of the measures is suitable for various professional jobs and construction sites, especially whether the construction safety technical measures of new technologies, new equipment, new processes and new materials are feasible. Check whether the construction site safety guarantee system is sound and perfect, whether the safety responsibility system from the first responsible person to other responsible persons to each team is decomposed and implemented, and whether there is a safety management supervision network. Check whether the labor protection of safety equipment during construction is complete, check the possible collapse or landslide of steep cliffs and deep pits, and regularly carry out inspections on fire safety, seasonal rainy season flood control, winter antifreeze, heatstroke prevention and typhoon prevention. If there is any nonconformity in the inspection, it shall be rectified within a time limit and given to informed criticism. 3, pay attention to the effective implementation of safety measures, pay attention to the implementation of safety measures in the construction process is an important link to do a good job in construction safety. A, before bricklaying foundation, check whether there is soil wall cracks, water invasion, freezing or deformation, collapse, and so on and so forth. When the width of the pipe trench is less than 3m, the side of the masonry station should have an operating width of 40cm. When building a deep foundation trench, the upper and lower foundation trenches must be provided with working ladders or ramps, and it is forbidden to jump over the foundation trench at will, trample on masonry or reinforce the soil wall support. When the floor is more than one floor or the height is more than 4m, the inner scaffold must set up a safety net, and the outer scaffold should set up a protective fence and skirting board before laying. It is forbidden to stand on the top of the wall to scrape, clean the wall or check the verticality of the big corner, and it is also forbidden to stand on the wall to lay bricks. Bricks are not allowed to bounce outward on the scaffold, but should bounce to the wall when broken. No one is allowed to sit on the protective fence, and no one is allowed to walk on the top of the wall being bricked; Second, when installing the work for more than 3 steps, the operator must wear a safety belt cap and hang the rope on his body with a pole. When scaffolding is erected, in case of strong wind or lightning storm above level 6, the scaffold must stop working above level 4, and the height is above 20 meters, and the wind power exceeds level 5. When erecting shelves near high-voltage lines, the distance between overhead distribution lines with 10 kV and below should be greater than 2.55 meters, and the distance between high-voltage transmission lines with 22 kV and above should be greater than 5 meters. The choice of the shelf can be based on the actual situation of the project, but the shelf must have sufficient firmness and stability. During the construction period, under the action of allowable load and climate temperature change, it is not allowed to deform, tilt or shake, and there must be enough working face to meet the needs of workers' operation, material stacking and construction vehicles. 3. There shall be no inflammable and explosive articles within 5m of the welding operation site. Before work, carefully check whether the welding equipment is idling, and welding can be carried out only after there is no problem. When working, the temperature around the gas cylinder should be kept above 10℃ to reduce gas moisture. Welding power supply should be stable, and the primary voltage fluctuation during welding should not be greater than 5%, otherwise welding is prohibited. When it rains, open-air welding operations should generally be stopped without special measures. In order to prevent electric shock, you must abide by the relevant electrical safety regulations; Fourthly, the surface of wire rope of hoisting machinery and rigging is worn. When the corrosion reaches 10% of the steel wire diameter, it should be replaced. When the broken wire exceeds the specification, it must be replaced. If it must be used, the load should be reduced accordingly. Hooks and snap rings should be scrapped and replaced if they are permanently deformed or cracked, and should be replaced when the cross section height of hooks is worn to 10%. Fifth, Plaster workers should check whether the shelves and high stools are firm before operation.