Current location - Education and Training Encyclopedia - Education and training - Operating standard of student driving test 16 project.
Operating standard of student driving test 16 project.
Subject III 16 Operating Standards

1. Get on the bus.

Drive around the car for a week, check the appearance of the car and the safety of the surrounding environment, and close the door when opening and closing the door; Seat belt, seat adjustment, check reset light, gear position and ignition switch; Then report to the instructor to prepare for the exam.

Simulated lighting

Don't grab the sound, put your hands on the light pole to avoid being in a hurry after hearing the sound, and keep the light on for 3 seconds.

begin

One step, two gears, three steering, four horns and five handbrake. Step on the clutch to the end, put it in the first gear, turn on the left turn signal, press the horn twice, release the brake, turn to the left through the rearview mirror to observe the traffic situation at the left rear, and slowly lift the clutch. When it reaches the semi-linkage point, the vehicle starts to start.

Meet the car

After hearing the voice prompt "There is a car ahead", pay attention to the coming car ahead, control the speed, and keep a safe distance from the opposite car when passing.

5. Add and delete files

According to the speed of the vehicle, shift gears reasonably, shift gears smoothly, and the vehicle does not move. Note: 1 gear 0-10 km/h; 10km/h-20km/h frequency; 20km/h-30km/h in 3rd gear; The fourth gear is 30 km/h -40 km/h.

Change lanes

Turn on the left turn signal for 3 seconds, observe the surrounding traffic through the rearview mirror first, and then change lanes after confirming safety.

7, through the crosswalk

Slow down in advance, reduce the speed to below 30km/h, and pass slowly. If pedestrians are crossing the road, they should stop to avoid.

8. Go through the school area

Slow down in advance, the speed must be reduced to less than 30km/h, and pass slowly. In case of students, you should take the initiative to stop and avoid.

9. Pass the bus stop.

Slow down in advance, the speed must be reduced to below 30km/h, and pass slowly.

10, go straight through the intersection.

Slow down in advance, observe the road traffic situation, and pass the intersection smoothly after confirming safety.

1 1, turn around

Turn on the left turn signal for more than 3 seconds, observe the surrounding traffic through the rearview mirror, and complete the U-turn in the designated area on the premise of confirming safety.

12, overtaking

Turn on the left turn signal for more than 3 seconds, observe the traffic outside the car through the rearview mirror, and complete the overtaking action after confirming safety.

13, turn left at the intersection.

Slow down in advance, reduce the speed to below 30km/h, turn on the left turn signal for more than 3 seconds, and complete the left turn.

14. Go straight.

Before driving in a straight line, reduce the speed to less than 30 km/h and drive in third gear. When driving, gently hold the steering wheel at three or nine o'clock with both hands, look ahead, select the reference accurately, and fine-tune the steering wheel when the vehicle deviates. Note: the range of correction can only be within 5 degrees.

15, turn right at the intersection.

Slow down ahead of time, reduce the speed to below 30km/h, turn on the right turn signal for more than 3 seconds, and complete the right turn.

16, pull over

When you hear the voice prompt "Pull over ahead", slow down in advance, reduce the speed to below 10km/h, and shift to a new gear.

Turn on the left turn signal for more than 3 seconds, and observe the traffic situation through the rearview mirror. When it is safe, pull over to the right, keep the right car body within 30cm of the road edge line, step on the clutch brake, and put it in neutral to tighten the handbrake.

Before getting off the bus, be sure to observe the left rearview mirror and make sure there is no car coming from behind before getting off.