Graduation design (thesis) topic of mechatronics specialty
1. CNC internal chip removal deep hole drilling machine-overall and drilling system design
2. Kinematics analysis of beam pumping unit.
3. Design of clamping device and electrical control system of semi-automatic thin-walled copper pipe bender.
4. Design of honing head rotary CNC deep hole powerful honing machine tool.
5. Design of grounding device for screw pump driven by synchronous motor.
6. Casing running load and safety analysis of test well
7. Design of EDM deep hole nesting processing system
8. Semi-automatic thin-walled copper pipe bender-integral and spatial bending design
9. Design of hydraulic disc brake system for drilling winch
10. Structural design of automatic drilling system of drilling rig
1 1. Failure mechanism of downhole casing and analysis of confining pressure stress
12. Analysis of wear degree and residual strength of technical casing
13. Design of javelin valve type airtight oil well pump
14. design of magnetic drive petrochemical process pump
15. mechanical analysis of completion string of high-yield gas well
16. design of JC-60d hydraulic drilling winch
17. 3D feature modeling and structural optimization analysis of workover rig derrick
18. design of deep hole honing system for non-rotating parts
19. design of the fuselage part of the integrated graphite electrode grinding machine
20. Mechanism analysis and database design of common complex drilling conditions.
2 1. design of large diameter deep hole drilling system with internal chip removal
22. The design of the ground pump for rapid discharge after the jet pump is pressurized.
23. Design of WOB loader for horizontal well bit
24. The design of ring valve airtight oil well pump
25. Spectrum analysis and fault diagnosis of gearbox vibration signal
26. CNC gun drilling machine tool-overall and drilling system design
27. Design of new gear winch for 27.ZJ50 electric drive drilling rig
28. The design of front-mounted beam pumping unit
29. Design of fixed liquid-driven jet pump oil production device
30. Design of hydraulic feedback thickening pump
3 1. Design of automatic unloading system for drill pipe on offshore drilling platform
32. Design and calculation of XJ-350 workover rig winch
33. Design of reciprocating pump experimental device
The design of 34. 40 hydraulic top drive device
35. Design of top drive device test bench
36. Design of Power Deceleration System of10 Pumping Unit
37. Ultra-thick-walled casing and its collapse strength analysis
38. Design of cuttings cleaning machine
39. PLC control program design of traffic lights at intersections
40. Design of centrifugal perfusion pump
4 1. design of single-stage oil pump
42. The design of workpiece rotary CNC deep hole powerful honing machine tool.
43. Design of workbench and cooling system of NC chip removal deep hole drilling machine.
44. Crankshaft end machining combined machine tool-overall and hydraulic system table
Design and analysis of 45. 10 transmission chain ultra-long stroke pumping unit
46. The design of hydraulic pumping unit
47. Design of gas-driven jet pump oil production device
48. Structural design of rodless reciprocating underground pumping unit
Design and analysis of 49.8- 1/2 inch rotary steering drilling tool
50. Design of rotary plunger oil well pump with spiral valve cover
5 1.ZJ40 drilling rig transmission scheme design and winch drum shaft design
52. Casing Subsidy Operation 512 Downhole Device Design.
53. Design of horizontal deep hole drilling system for non-rotating parts
54. Design and calculation of heterogeneous beam pumping unit
55. The design of spiral plunger rotary plunger oil well pump
56. Structural design of top drive drilling rig
57. Energy-saving transformation of conventional beam pumping unit
58. The design of linear motor downhole drive oil production device
59. Design and calculation of XJ-250 workover rig winch
60. The design of the combined machine tool for machining the two ends of the crankshaft-the right headstock and the copying machine tool.
6 1. Optimal design of structural dimension parameters of double pulley straight flat pumping unit
The design of 62. Model 50 electric top drive device
63. The shape design of left headstock, a combined machine tool for machining holes at both ends of crankshaft.
64. Design of solenoid valve for pneumatic indexing system
65. Design of automatic marking device and control interface
66. Research on chart optimization method of carbon fiber sucker rod production device
67. Analysis of casing collapse strength calculation formula
68. Study on dynamic characteristics of offshore drilling riser
69. The design of eccentric pumping unit
70. Design of centrifugal sand pump