Papers are often used to refer to articles that conduct research in various academic fields and describe academic research results, which are referred to as papers for short. It is not only a means to discuss problems in academic research, but also a tool to describe academic research results in academic exchanges. Including academic papers, graduation papers, dissertations, scientific papers, achievement papers and so on. The following is a supplement to the references in my graduation thesis, which I carefully arranged. Welcome everyone to learn from it, I hope it will help you.

The introduction of graduation thesis will quote a large number of references, and the labeling of these references is a headache. After the first draft is written, some references will be added or deleted after revision, and the serial number of the document will change, resulting in workload problems. As far as I know, the following are several common solutions, and their advantages and disadvantages are obvious.

(1) The most vulgar and stupid method. List the references while writing, and manually adjust the serial number of the references again if it is modified;

Workload: xxxxx

Flexibility: x

(2) Compare the methods of "speculation". Students who have studied the course of "Literature Retrieval and Utilization" can use literature management software such as Refworks and NoteExpress to mark references. General process: First, manually input the used references into these softwares, then select a reasonable document labeling format, and finally label the full text of WORD. Possible problems (taking Refworks as an example): every time a document is generated, a new WORD document will be generated, and a new document will be generated after the next modification, and the reference source of the document needs to be edited again;

Workload: xxxx

Flexibility: xxx

(3) The quickest and simplest method (recommended): Use the function of WORD itself. First, list the references at the end of the article (pay attention to the automatic numbering of references), then "citation"-cross-citation-citation type: numbering item-citation content-paragraph number-select to insert as hyperlink-and finally select the cited documents, thus completing the whole labeling process. If you modify a document, you only need to select the full text, right-click the update field, and you can automatically readjust the serial number of the document. And hold down CTRL+ left click in the text to jump to the corresponding literature.

Workload: xx

Flexibility: xxxxx

(4) Faster but more professional method: You can use the bookmark function of WORD to combine with (3). The function is similar, but it is better than (3) that when the mouse stops at the reference place, it will display the reference information, which is more suitable for reading.

Workload: xxx

Flexibility: xxxxx

To sum up, method (3) is recommended. If it is not too troublesome, you can consider using method (4).

The role of references is sometimes more important than the article itself. Readers can learn about the research trends in a certain field through references. Therefore, it is absolutely helpful for undergraduate graduation thesis to pay more attention to the annotation of references and learn good methods (especially when the thesis is published, the requirements for references are more stringent).

Notes on the References of Graduation Thesis 2 When we are writing a thesis, the notes and references of the thesis often appear on the same page. So, how do we annotate these two paragraphs separately? For the notes on the same page, the information used in the paper will be indicated at the bottom of this page, and the references will generally be listed at the end of the paper.

So, how are paper notes added? Where should I add it? We often use some technical terms in thesis writing, but these technical terms may not be understood by ordinary people. At this time, it is necessary to explain the technical terms in detail, and this explanation part is what we call annotations. Insert a footnote after a professional noun and finish it in wps: click the wps text menu >; Insert > Reference > Footnotes and Endnotes > Select the footnote position and numbering format, and then mark the same number at the bottom of the annotation page to explain the annotation text.

So how are citations annotated? References are divided into sequential coding system and author year system. Sequential coding system, according to the citation order, marks the corresponding citation contents in the text with upper corner markers, such as [1], [2] or ① and ②, and the references at the end of the text are listed in this annotation order; Author's year system, the author and publication year are indicated in brackets in the citation part, such as (Li xx, 20 14), and the references at the end of the article are generally arranged in linguistic order first, and then in alphabetical order by the author's name.

The order of the references listed at the end of the paper must not be wrong. When writing a paper, it is best to quote references and write down the names of the documents, so that it is not easy to miss mistakes.

;