P2P terminals can be installed on any host in the local area network. If it is an enterprise user, it is recommended to use an independent host as the controller to ensure better control effect. If your network uses a proxy server to provide public network access, then be careful not to install software on the proxy server, which will cause the software to be unable to control other hosts normally.

2. Will 2. P2P Terminator Causes Network Congestion?

Version 4.0 of P2P Terminator adopts the latest driver of WinPcap and optimizes the core code. After the actual test of Intel dual-core 1.6G CPU and 1G DDR memory, the maximum bandwidth processing speed can reach 60Mbps. At present, the broadband access bandwidth of home ADSL is mostly 5 12K or 1Mbps, and the access bandwidth of enterprises is generally much less than 60Mbps, so using P2P terminator to manage the network will not cause network congestion.

Software function use problem

1. Software prompts that the underlying engine cannot be started?

The first step is to confirm whether the control network card has been set up: you can use the "System Settings" panel on the left side of the software-> "advanced options"->; "Network card settings" specifies the control network card. Step 2: Check whether the winpcap driver is installed correctly: You can search wpcap.dll and packet.dll on the system disk, if so, delete them, reinstall the software and restart the computer. If the problem still cannot be solved, please contact us by email!

2. The software can't scan other hosts?

If you dial the Internet through the host computer and you are the dial-up host computer, the control function cannot be realized normally when the software is installed on your machine. If you surf the Internet through a broadband router, there may be two reasons why you can't find the host: (1) There are no other active hosts in the network now, so you can scan it another day; (2) Your lan switches has set up port isolation, so you need to log in to the switch to cancel this configuration.

3. Can't see the real-time bandwidth of other hosts?

You can't see the bandwidth of other hosts for the following reasons: (1) You didn't enable control (2) You didn't select the check box in front of the host you want to control (3) Other hosts installed ARP firewall software. If another host has an ARP firewall installed, you may not be able to effectively control the host.

4. Will the host list turn gray or orange?

Sometimes the host list item will turn gray, indicating that the host is offline; Sometimes the host list item will turn orange, indicating that you have disconnected the public network of the host.

5. Why can't I send messages to others?

Using Windows Messenger system service to realize P2P terminal software to send messages. If your computer disables or does not start the Messenger service, you will not be able to send messages. At the same time, if the receiving host disables or does not start the Messenger service, it will not be able to receive the messages you send.

6. What if there is a blue screen after the software runs?

If there is a blue screen when running P2P Terminator, it is generally caused by software conflicts, such as some personal firewall software. During the test, it was found that Fengyun firewall would lead to blue screen when running P2P terminator. I suggest you uninstall your personal firewall first, verify it and see if the problem is solved.

7. What if the software prompts an error when selecting a network card and exits?

The software prompt error may be caused by incorrect installation of winpcap driver. You can download the winpcap installation package and install it, then restart your computer and try again.

Network management authority problem

1. What is network management permission?

Network management authority is a new concept introduced in version 4.0, because if many people in a network need to run P2P Terminator at the same time, it is necessary to determine who has network management authority, the computer with higher authority can execute it, and the computer with lower authority needs to quit the software. The management authority I * * * is divided into five levels: the lowest, the lower, the medium, the higher and the highest. By default, it is the lowest authority after software installation.

2. The software prompts to find a P2P terminator with higher authority in the network to run and then quit?

This prompt appears in the software because someone in the local area network has started to run P2P terminator, and the network management authority of this host is higher than your computer.

3. The software prompts to find a higher version of P2P Terminator running in the network and then quit?

This prompt appears in the software because someone in the network has started to run P2P terminator, and the P2P terminator software version of this host is higher than yours. I suggest you upgrade to the latest version as soon as possible.

4. The software prompts that you need to quit P2P Terminator before others can run it?

This prompt appears in the software because someone in the network has started to run P2P terminator, and the network management authority of this host is the same as your own computer, and your running time in a day is longer than this host. To ensure fairness, you need to quit so that this host can run the software.

5. How to improve your network management authority?

P2P Terminator provides you with a way to improve the local network management authority. When you need to search online, you can use the "Super Fast Search" software that comes with P2P Terminator to search the web page, and P2P Terminator will increase your network management authority according to your search contribution. The more frequently used, the higher the network management authority. In addition, administrative rights are updated according to the date. When the date changes, the network management authority of P2P Terminator will be automatically restored to the original minimum state.