On-site staff should receive regular training, learn emergency rescue methods, correctly release power, know cardiopulmonary resuscitation, stop bleeding, bandage, transfer and transport the wounded, and give first aid to trauma or poisoning.
If someone is found to get an electric shock, the power supply should be cut off immediately, so that the person who gets an electric shock can be separated from the power supply and first aid should be given. If you work at high altitude, you must pay attention to prevent the danger of falling from high altitude.
Relevant knowledge of electrical safety working procedures
1, what is the policy of power production?
A: The policy of power production is "safety first, prevention first".
2, who should be familiar with the relevant parts of the electrical safety work procedures?
A: Workers at all levels, production workers, technicians and relevant personnel engaged in the design, installation, test and maintenance of power generation and power supply (including rural power) in the power industry should be familiar with the relevant parts of the "Electric Power Safety Work Regulations".
3. How to deal with people who violate electrical safety work rules?
Answer: Those who violate the electrical safety regulations should be carefully analyzed, strengthened education and dealt with seriously according to the situation. Those who cause major accidents shall be given administrative or criminal sanctions according to the seriousness of the case.
4, it is forbidden to use anything to lift heavy objects and lifting block?
Answer: It is forbidden to use any pipeline to hang heavy objects and blocks.
5. What measures should be taken to remove the cover plate during maintenance?
Answer: If the cover plate needs to be removed during maintenance, a temporary fence must be set up.
6. What are the safety regulations for the height of railings and guard plates at the production site?
Answer: The height of the railing at the production site shall not be less than 1050 mm, and the height of the guard plate shall not be less than100 mm. ..
7. What are the rules for laying iron plates on all stairs, platforms and passages?
Answer: The iron plates laid on all stairs, platforms and passages must be firm. The surface of the iron plate should be textured to prevent slipping.
8. What are the rules for shared lighting in the workplace inside and outside the production plant?
Answer: The shared lighting in the workplace inside and outside the production plant should ensure sufficient brightness. In the operation panel, important instruments (such as water level gauge, etc. ), main stairs, passages and other places, emergency lighting must also be set up.
9. What necessary fire-fighting equipment should be equipped in the production workshop and warehouse?
Answer: Production workshops and warehouses should be equipped with necessary fire-fighting equipment, including fire hydrants, hoses, fire extinguishers, sand boxes, asbestos cloth and other fire-fighting tools.
10. What flammable items are prohibited in the workplace?
A: It is forbidden to store flammable items in the workplace: gasoline, kerosene, alcohol, etc.
1 1. What connections should the tubing use as little as possible?
Answer: Pipes should be connected with flanges as little as possible.
12, what are the regulations for heating heat sources in production workshops?
Answer: The heat source heated in the production workshop should be managed by a special person. The pressure should meet the requirements of heating equipment. If a heat source with high pressure is used, it must be equipped with a pressure relief device and a safety valve.
13. What are the safety regulations of the factory building?
A: The workshop must be inspected regularly. The factory building structure should be free from inclination, cracks, weathering and collapse, and the doors and windows should be complete.
14. What are the regulations for elevators installed in production plants before use?
Answer: Before the elevator installed by the manufacturer is used, it should be inspected by the relevant departments to obtain the certificate, and the safe use regulations and regular inspection and maintenance system should be formulated.
15. What first aid methods and common sense should all staff learn and be familiar with?
Answer: All staff should learn the first aid methods of electric shock asphyxia and cardiopulmonary resuscitation, and be familiar with the first aid knowledge about burns, scalds, trauma and gas poisoning.
16. What are workers forbidden to wear when entering the production site?
A: Workers are forbidden to wear slippers and sandals when entering the production site, and women workers are forbidden to wear skirts and high heels.
17. Anyone who enters the production site must wear a safety helmet, except where?
Answer: Anyone who enters the production site (except office, control room, duty room and maintenance team) must wear safety helmet.
18. What safety measures should be taken to prevent the machine from rotating during maintenance?
Answer: The safety measures to prevent the machine from rotating during maintenance are: cutting off the power supply; Cut off wind source, water source and steam source; All related rams, valves, etc. Should be closed; Warning signs are hung at all the above locations. Reliable braking measures should also be taken when necessary.
19. Which part of the machine is forbidden to be cleaned, wiped and lubricated during operation?
Answer: It is forbidden to clean, wipe and lubricate the rotating and moving parts of the machine during operation, and it is forbidden to put your hands into the fence.
20. Where is it forbidden to walk or sit?
Answer: It is forbidden to walk or sit on railings, pipes, backrest wheels, safety covers or bearings of running equipment. If you have to work on a pipe, you must take safety measures.
2 1. Where should we try to avoid getting close and staying for a long time?
Answer: Close to and in places that may be scalded for a long time, such as flanges, valves, manhole doors, inspection holes and explosion-proof doors, safety doors, deaerator, heat exchanger, drum water level gauge, etc.
22. What are you not allowed to touch with wet hands?
Answer: Wet hands are not allowed to touch electric equipment such as electric shock light switch (except in safe voltage).
23, found that the power switch shell and wire insulation damage or incomplete or live part exposed, how to deal with? Answer: If the insulation of the power switch shell and wire is damaged or incomplete or the live part is exposed, you should find an electrician to repair it immediately, otherwise it is not allowed to be used.
24, found someone get an electric shock should be how to first aid?
Answer: If someone is found to be electrocuted, the power supply should be cut off immediately, so that the electrocuted person can be separated from the power supply and given first aid. If you are working at high altitude, you must pay attention to prevent falling from high altitude during rescue.
25. What fire extinguisher should be used when electrical equipment and generators and motors that may be charged catch fire?
Answer: Dry fire extinguishers, carbon dioxide fire extinguishers or 12 1 1 fire extinguishers should be used to extinguish fires of electrical equipment, generators and motors that may be charged.
26. What breathing apparatus should rescuers use when fighting fires that may produce toxic gases?
Answer: Firefighters should use positive pressure fire fighting air respirator when fighting fires that may produce toxic gases (such as cable fires).
References:
Electrical safety work procedures-Baidu Encyclopedia